JVC HR-J765EK Access Main Menu, Access Mode SET, Select Picture Control SET Mode, Adjust Tracking

Page 17

ADVANCEDOPERATIONS

17

Playback Pic- ture Adjustment

Picture Control

This feature helps you to adjust the playback picture quality according to your preference. *The default setting is "AUTO."

ACCESS MAIN MENU

SCREEN

1

MENU

0

?

3

4

TV PROG

OK

1 Press MENU.

 

 

ACCESS MODE SET

 

SCREEN

 

 

Move the highlighted bar (pointer) to "MODE SET" by

2 pressing %Þ, then press OK or #.

 

 

SELECT PICTURE

 

3

CONTROL SET MODE

Move the highlighted bar

MODE SET

(pointer) to "PICTURE

ON

B. E. S. T.

Manual Tracking

Your video recorder is equipped with automatic tracking control. For most tapes this will automatically adjust the tracking to suit the particular tape you are playing. In some circumstances it may be necessary to make manual tracking adjustments. This is usually only associated with old or worn tapes or recordings made on old or worn recorders. If the automatic tracking control fails to operate correctly you will see noise bars across the picture as shown on the left below. To correct this you can override the automatic control and adjust the tracking manually by pressing the TV PROG buttons.

OVERRIDE AUTOMATIC

TRACKING

1

Press

on the remote to engage manual tracking.

 

ADJUST TRACKING

2

MANUALLY

Press TV PROG + or – to adjust tracking.

 

RETURN TO AUTOMATIC

 

TRACKING

 

Press

on the remote to re-engage automatic

3 tracking.

 

CONTROL" by pressing

 

 

PICTURE CONTROL

AUTO

%Þ, then press OK or #to

AUTO TIMER

OFF

select the desired mode.

O. S. D.

ON

AUTO: Provides optimised

AUTO SP=LP TIMER

OFF

 

 

 

picture benefits of

 

 

 

B.E.S.T. Picture

[5°] =

 

 

System. Normally

[MENU] : EXIT

 

 

select AUTO.

 

 

EDIT:

Minimizes picture degradation during editing

 

(recording and playback).

 

SOFT:

Reduces image coarseness when viewing

 

 

overplayed tapes containing a lot of noise.

 

SHARP: Clearer, sharper-edged picture when viewing

 

images with lots of flat, same-coloured surfaces

 

such as cartoons.

 

 

NOTES:

●When you select EDIT, SHARP or SOFT, the selected mode will not change until you select again.

●When you select EDIT to dub tapes, be sure to select AUTO after you finish dubbing the tapes.

RETURN TO NORMAL

SCREEN

4 Press MENU.

NOTES:

●When B.E.S.T. is OFF, "PICTURE CONTROL" switches automatically from AUTO to NORM.

●Select EDIT when you are dubbing tapes. Refer to page 24.

NOTE:

When a new tape is inserted, the recorder returns to the automatic tracking mode automatically.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents HR-J765EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVGo to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search Pause During PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningSatellite Receiver Users Press SP/LPAccess Video PLUS+ Screen Express Timer ProgrammingStart Time Enter ProgrammePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Access Mode SET Access Main MenuSelect Picture Control SET Mode Adjust TrackingS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Receiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackActivate Index Search Looking For Scene You WantActivate Instant Review Skip Over UnwantedAutomatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Engage Auto Satellite Prog REC ModePress SP/LP on the remote control to set the tape speed SET Edit Mode SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Make ConnectionsEdit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Select ModeAuto SP→LP Timer Playback Activate RepeatRepeat Playback Ntsc PlaybackTelevision Connection To Stereo SystemAudio Cable not provided Audio OUT Mains outletExit Video Channel SET Mode Access Video CHAN- NEL SET ModeVideo Channel Set SET Video ChannelWith RF Connection Access Video Chan NEL SET ModeAuto Channel Set Tuner SetSET Procedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Switch Stations Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetAccess Initial SET Screen Video Plus+ SetupAccess Guide Prog SET Screen Enter Guide Prog NumberRemain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Check the programmed data and re Cassette with the Record Safety tabBlinking Intact Blinks for 10 seconds Front View IndexTape Speed Indicators display mode of recording light Audio OUT L/R Connectors enableRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoDA4 Double Azimuth helical Maximum recording time
Top Page Image Contents