JVC HR-J765EK Select Preset to Watch, SET Counter Display, Reset Counter, Engage ITR Mode

Page 11

 

 

REW

FF

STANDBY/ON

 

 

 

 

 

 

TV PROG/

 

TIMER

 

JOG

VIDEO(MONO)L –AUDIO– R

 

 

SHUTTLE

REC LINK

TV PROG

 

TV

PROG

RECORD

 

11

Record One Programme While Watching Another

SELECT PRESET TO WATCH

1 Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you wish to view.

The programme selected with the TV’s preset controls appears on the TV screen while the one selected with the recorder's TV PROG buttons is recorded on the tape.

Elapsed Recording Time Indication

You can check the exact time of a recording.

1 2 3

4 5 6

7 8 9

00000

1

?

3

–:–

2

4

TV PROG

 

1

 

SET COUNTER DISPLAY

 

 

Press –:–until a counter reading appears on the

 

 

dispay panel.

 

2

 

RESET COUNTER

 

 

Press 0000 before starting recording or playback.

 

 

 

 

 

The counter is reset to “0:00:00” and shows the exact

 

 

elapsed time as the tape runs.

Instant Timer Recording (ITR)

This easy method allows you to record for any length of time from 30 mins. to 6 hours (selectable in 30-min. increments), and shuts off the recorder after recording is finished.

START RECORDING

1 Press RECORD on the recorder.

ENGAGE ITR MODE

2 Press RECORD again. "" blinks and “0:30” appears on the front display panel.

Tape Remaining Time

DISPLAY REMAINING TIME

1 Press –:–until the time remaining on the tape appears.

The display panel shows the tape remaining time with

" " displayed.

By pressing the –:–button, you can change the display to show the counter reading, preset position*, clock time or tape remaining time.

*Preset position is not displayed during playback.

NOTE:

Depending on the type of tape used, there may be times when the tape remaining time reading may not appear right away, or is not correct. "– –:– –" may sometimes appear, or the display may blink on occasion.

SET RECORDING

DURATION

3 If you want to record for more than 30 minutes, press RECORD to extend the time. Each press extends recording time by 30 minutes.

NOTE:

You can only perform ITR using the RECORD button on the recorder's front panel.

Image 11
Contents HR-J765EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVGo to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search Pause During PlaybackRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeVideo Plus+ Timer Programming Press SP/LP Timer WarningPDC Recording Satellite Receiver UsersEnter Programme Express Timer ProgrammingAccess Video PLUS+ Screen Start TimePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Adjust Tracking Access Main MenuAccess Mode SET Select Picture Control SET ModeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback During Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionSkip Over Unwanted Looking For Scene You WantActivate Index Search Activate Instant ReviewSatellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording Outdoor Unit Satellite CableBefore performing the following steps Engage Auto Satellite Prog REC ModePress SP/LP on the remote control to set the tape speed Make Connections SET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto Timer Select ModeAuto SP→LP Timer Ntsc Playback Activate RepeatPlayback Repeat PlaybackAudio OUT Mains outlet Connection To Stereo SystemTelevision Audio Cable not providedSET Video Channel Access Video CHAN- NEL SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Access Video Chan NEL SET ModeAuto Channel Set Tuner SetSET Is displayed on the screen Screen preset positionsProcedures After Scan CompletedStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Close Confirmation Access Manual Channel SET ScreenSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetEnter Guide Prog Number Video Plus+ SetupAccess Initial SET Screen Access Guide Prog SET ScreenRemain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Check the programmed data and re Cassette with the Record Safety tabBlinking Intact Blinks for 10 seconds Front View IndexTape Speed Indicators display mode of recording light Audio OUT L/R Connectors enableRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoDA4 Double Azimuth helical Maximum recording time