JVC HR-J765EK setup guide Load a Cassette, Point, Start Playback, Stop Playback

Page 8

8

BASICOPERATIONS

Playback

Turn on the TV and select the VIDEO channel (or AV mode).

The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.

LOAD A CASSETTE

Make sure the window side is up, the rear label side is

1 facing you and the arrow on the front of the cassette is

STANDBY/ON

 

TIMER

VIDEO(MONO)L –AUDIO– R

REC LINK

3

PLAY

1

REW

TV PROG

2

SHUTTLE

FF

TV PROG/

JOG

SHUTTLE

point toward the recorder. Don’t apply too much

pressure when inserting.

The recorder power comes on automatically and the

counter is reset to 0:00:00.

If the record safety tab has been removed, playback

begins automatically.

FIND PROGRAMME START

POINT

 

PROG

JOG

TV

STOP/EJECT

 

4

 

 

 

2

If the tape is advanced past the start point, press REW

or turn the SHUTTLE ring to the left.

To go forward, press FF or turn the SHUTTLE ring to the

 

right.

 

 

 

START PLAYBACK

TV/VCR

1 2 3

4 5 6

7 8 9

0

3

LAY

1

?

2 REW

4 STOP

3

2

4

TV PROG

FF 2

PAUSE

3

Press PLAY. "BEST" appears blinking in the recorder's

display panel during automatic tracking (pg. 18).

 

Playback picture quality of LP recordings will not be

 

as high as SP recordings.

 

 

 

STOP PLAYBACK

 

Press STOP on the remote or STOP/EJECT on the

 

recorder’s front panel. Then press STOP/EJECT to

4 remove the cassette.

INFORMATION

When using the AV connection (pg. 5), initiating playback causes the VCR indicator to light and the TV to automatically enter AV mode. To return the TV to TV mode after playback is complete, press TV/VCR so that the VCR indicator turns off.

*Depending on the type of TV used, TV/VCR button does not function as described above.

Tape Position Indicator

The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “” in relation to “0” (beginning) or “+” (end)

shows you where you are on 0 + the tape.

”O.S.D.” (pg. 26) must

be set to “ON”, or the

indicator will not appear. Beginning

Á

+ +

1:23:45 REMAIN 2:35

End

Usable cassettes

Compact VHS camcorder recordings can be played on

this video recorder. Simply place the recorded cassette

into a VHS Cassette Adapter and it can be used just like

any full-sized VHS cassette.

This video recorder can record on regular VHS and Super

NOTE:

Depending on the type of tape used, there may be times when the indication is not correct.

VHS cassettes. However, it will record and play back

regular VHS signals only. It is not possible to play back a

recorded Super VHS tape.

Image 8
Contents HR-J765EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV Back of RecorderGo to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingSatellite Receiver Users Press SP/LPExpress Timer Programming Access Video PLUS+ ScreenStart Time Enter ProgrammeSET PDC Mode Press TV Prog +/- toCheck, Cancel And Replace Programmes Access Main Menu Access Mode SETSelect Picture Control SET Mode Adjust TrackingS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Selecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackLooking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedAerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Engage Auto Satellite Prog REC ModePress SP/LP on the remote control to set the tape speed SET Recording DECK’S Input Mode SET Edit ModeEdit To Or From Another Video Recorder Make ConnectionsSET RECORDER’S Input Mode Edit From a CamcorderStart Camcorder Start RecorderAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Select ModeAuto SP→LP Timer Activate Repeat PlaybackRepeat Playback Ntsc PlaybackConnection To Stereo System TelevisionAudio Cable not provided Audio OUT Mains outletAccess Video CHAN- NEL SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelAccess Video Chan NEL SET Mode With RF ConnectionAuto Channel Set Tuner SetSET Screen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Access Manual Channel SET Screen Switch StationsSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup Access Initial SET ScreenAccess Guide Prog SET Screen Enter Guide Prog NumberQuestions And Answers Remain lit on the display panel. Is there Problem?Troubleshooting Check the programmed data and re Cassette with the Record Safety tabBlinking Intact Blinks for 10 seconds Index Front ViewAudio OUT L/R Connectors enable Tape Speed Indicators display mode of recording lightRemote Control Auto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helical