JVC HR-J765EK Auto Tracking Button enables/disables auto, VCR, TV Prog +/-,TV +/-, TV Muting

Page 47
JVC TV. column.

)WEEKLY Button enables timer recording of weekly serials. pg. 13, 15

qAUX Button selects recorder's auxiliary input mode. pg. 24

w Button engages timer-standby mode. pg. 13, 15

eDATE +/– Button inputs date of programme for timer recording. pg. 14

rTV PROG +/– Button — same as button on recorder. pg. 10

t30 SEC Button initiates a 30-second period of fast-motion playback. pg. 21

yAuto Tracking Button enables/disables auto

tracking mode during playback pg. 17

SP/LP () Button selects tape speed. pg. 10

uPlay Button — same as button on recorder. pg. 8, 9

iFast Forward [FF] Button fast-forwards tape pg. 8; initiates high-speed forward search. pg. 9

oPause Button — same as button on recorder. pg. 9

pOK Button enters selections made in on-screen menus. pg. 18

Q @ #Button initiates functions such as Index Search pg. 19, variable-speed search, frame by frame playback. pg. 9

TV +/–Buttoncontrols volume of connected "Operating JVC TVs" in the right

47

How To Use

The remote control can operate most of your video recorder's functions, as well as basic functions of JVC TV sets. (See below.)

Point the remote control toward the sensor window.

The maximum operating distance of the remote control is about 8 m.

Operating JVC TVs

To operate your TV, while holding down the TV button, press the corresponding button: STANDBY/ON , TV/

VCR, TV PROG +/–,TV +/–, (TV Muting).

NOTES:

When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover.

Depending on the type of JVC TV, there may be cases where some or all functions cannot be operated using the remote control.

If the remote control doesn't work properly, remove its batteries, wait a short time, replace the batteries and then try again.

Image 47
Contents HR-J765EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVGo to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search Pause During PlaybackRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeVideo Plus+ Timer Programming Press SP/LP Timer WarningPDC Recording Satellite Receiver UsersEnter Programme Express Timer ProgrammingAccess Video PLUS+ Screen Start TimePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Adjust Tracking Access Main MenuAccess Mode SET Select Picture Control SET ModeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback During Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionSkip Over Unwanted Looking For Scene You WantActivate Index Search Activate Instant ReviewSatellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording Outdoor Unit Satellite CableBefore performing the following steps Engage Auto Satellite Prog REC ModePress SP/LP on the remote control to set the tape speed Make Connections SET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto Timer Select ModeAuto SP→LP Timer Ntsc Playback Activate RepeatPlayback Repeat PlaybackAudio OUT Mains outlet Connection To Stereo SystemTelevision Audio Cable not providedSET Video Channel Access Video CHAN- NEL SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Access Video Chan NEL SET ModeAuto Channel Set Tuner SetSET Is displayed on the screen Screen preset positionsProcedures After Scan CompletedStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Close Confirmation Access Manual Channel SET ScreenSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetEnter Guide Prog Number Video Plus+ SetupAccess Initial SET Screen Access Guide Prog SET ScreenRemain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Check the programmed data and re Cassette with the Record Safety tabBlinking Intact Blinks for 10 seconds Front View IndexTape Speed Indicators display mode of recording light Audio OUT L/R Connectors enableRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoDA4 Double Azimuth helical Maximum recording time