JVC HR-J765EK setup guide Access Video Chan NEL SET Mode, With RF Connection

Page 31

 

 

REW

FF

STANDBY/ON

 

 

 

 

 

 

TV PROG/

 

TIMER

 

JOG

VIDEO(MONO)L –AUDIO– R

 

 

SHUTTLE

REC LINK

TV PROG

 

STOP

31

With RF Connection

Before performing the following procedure, make sure that:

the mains power cord is plugged into the mains outlet.

the video recorder is turned off and there is no cassette inserted in the recorder.

the connected TV is turned on.

batteries have been installed in the remote control.

ACCESS VIDEO CHAN-

NEL SET MODE

1 Press and hold down STOP on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

1 2 3

4 5 6

7 8 9

0

1

?

2

4

TV PROG

OK

2 Press TV PROG+ or to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area. Refer to list on page 42 for details of broadcast stations in your area.

(Ex.) If channel 36 is available in your area

Then set your TV to UHF channel 36. (Refer to the instructions supplied with your TV set for how to do this.)

If the two vertical white bars appear clearly on the screen as shown in the illustration at bottom left, go to step 3.

If the two vertical white bars do not appear clearly, re- set the video recorder to another vacant channel and try again.

IMPORTANT

If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET MODE

TEST SIGNAL

The channel on which the screen on the left appears clearly in step 2 is your Video Channel.

3 Press OK.

To view picture signals from the video recorder, set your TV to the Video Channel.

Image 31
Contents HR-J765EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVYour TV via both an RF cable and a 21-pin Before performing the following procedure, make sure thatGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search Pause During PlaybackRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeVideo Plus+ Timer Programming Press SP/LP Timer WarningPDC Recording Satellite Receiver UsersEnter Programme Express Timer ProgrammingAccess Video PLUS+ Screen Start TimePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Adjust Tracking Access Main MenuAccess Mode SET Select Picture Control SET ModeTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Playback RecordingOr press Record on the recorder During Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionSkip Over Unwanted Looking For Scene You WantActivate Index Search Activate Instant ReviewSatellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording Outdoor Unit Satellite CablePress SP/LP on the remote control to set the tape speed Engage Auto Satellite Prog REC ModeBefore performing the following steps Make Connections SET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto SP→LP Timer Select ModeAuto Timer Ntsc Playback Activate RepeatPlayback Repeat PlaybackAudio OUT Mains outlet Connection To Stereo SystemTelevision Audio Cable not providedSET Video Channel Access Video CHAN- NEL SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Access Video Chan NEL SET ModeSET Tuner SetAuto Channel Set Is displayed on the screen Screen preset positionsProcedures After Scan CompletedStoring Channels Manually Fine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Close Confirmation Access Manual Channel SET ScreenSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetEnter Guide Prog Number Video Plus+ SetupAccess Initial SET Screen Access Guide Prog SET ScreenRemain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Blinking Intact Blinks for 10 seconds Cassette with the Record Safety tabCheck the programmed data and re Front View IndexTape Speed Indicators display mode of recording light Audio OUT L/R Connectors enableRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoDA4 Double Azimuth helical Maximum recording time