JVC HR-J765EK setup guide Back of TV, Back of Recorder

Page 5

5

STEP

2

INSTALLATION

CONNECT VIDEO RECORDER TO TV

Place the recorder on a stable, flat surface.

Back of TV

Aerial connector

21-pin AV input connector (SCART)

Mains Power Cord

Mains outlet

RF Cable (provided)

 

21-pin SCART Cable

 

(not provided)

 

 

TV Aerial Cable

Make this

(not provided)

connection if

 

your TV has a

 

21-pin AV input

 

connector (SCART) in

 

order to reduce the

 

possibility of interference.

 

And if you are using a stereo

 

TV, you will need this cable

 

in order to enjoy stereo

 

playback of videotapes.

 

 

 

 

ENTREE

 

 

 

ANT. IN

 

 

SORTIE

 

AV2 ENTREE/DECODEUR

AV1 ENTREE/SORTIE

OUT

ANTENNE

R

IN/DECODER

IN/OUT

 

SORTIE

 

 

AUDIO

RF OUT

 

 

L

 

Back of Recorder

RF CONNECTION

To Connect To A TV With NO 21-pin AV input connector (SCART) . . .

1– Disconnect the TV aerial cable from the TV.

2– Connect the TV aerial cable to the ANT. IN jack on the rear panel of the recorder.

3– Connect the provided RF cable between the RF. OUT jack on the rear panel of the recorder and the TV’s aerial connector.

AV CONNECTION

To Connect To A TV With 21-pin AV input connector (SCART) . . .

1– Connect the aerial, recorder and TV as per “RF

CONNECTION”.

2– Connect an optional SCART cable between the AV1 IN/OUT connector on the rear panel of the recorder and the TV’s 21-pin AV input connector (SCART).

ATTENTION

Do NOT Plug the mains power cord into a mains outlet until all connections are completed.

Do NOT press the button on the recorder or on the remote control to turn on the recorder's power before you start the Auto Set Up procedure described on page 6.

AFTER YOU FINISH THIS STEP

Go to Step 3 – AUTO SET UP

Image 5
Contents HR-J765EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVGo to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search Pause During PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningSatellite Receiver Users Press SP/LPAccess Video PLUS+ Screen Express Timer ProgrammingStart Time Enter ProgrammePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Access Mode SET Access Main MenuSelect Picture Control SET Mode Adjust TrackingS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Receiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackActivate Index Search Looking For Scene You WantActivate Instant Review Skip Over UnwantedAutomatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Engage Auto Satellite Prog REC ModePress SP/LP on the remote control to set the tape speed SET Edit Mode SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Make ConnectionsEdit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Select ModeAuto SP→LP Timer Playback Activate RepeatRepeat Playback Ntsc PlaybackTelevision Connection To Stereo SystemAudio Cable not provided Audio OUT Mains outletExit Video Channel SET Mode Access Video CHAN- NEL SET ModeVideo Channel Set SET Video ChannelWith RF Connection Access Video Chan NEL SET ModeAuto Channel Set Tuner SetSET Procedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Switch Stations Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetAccess Initial SET Screen Video Plus+ SetupAccess Guide Prog SET Screen Enter Guide Prog NumberRemain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Check the programmed data and re Cassette with the Record Safety tabBlinking Intact Blinks for 10 seconds Front View IndexTape Speed Indicators display mode of recording light Audio OUT L/R Connectors enableRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoDA4 Double Azimuth helical Maximum recording time