JVC SR-V10E 18 EN, Next Function Memory, Repeat Playback, Manual Tracking, Soundtrack Selection

Page 18

18 EN

PLAYBACK (cont.)

Next Function Memory

The Next Function Memory “tells” the recorder what to do after rewinding. Before continuing, make sure the recorder is in the Stop mode.

a- For Automatic Start Of Playback

Press 3, then press 4 within 2 seconds. b- For Automatic Power Off

Press 3, then press 1 within 2 seconds. c- For Automatic Timer Standby

Press 3, then press # (TIMER) within 2 seconds.

NOTE:

The Automatic Power Off does not work if “AUTO TIMER” is set to “ON” ( pg. 45) and if any timer programming has been made. The recorder directly goes into the Timer-Standby mode after rewinding a tape.

Repeat Playback

Your recorder can automatically play back the whole tape repeatedly.

1Start playback.

Press 4.

2Activate Repeat Playback.

Press 4 and hold for over 5 seconds, then release.

●The Play indicator ($) on the front display panel blinks slowly.

3Stop Repeat Playback.

Press 8 at any time.

●Pressing 4, 3, 5 or 9 also stops Repeat Playback.

NOTES:

●Repeat playback is not possible with a cassette recorded in EP mode.

●To select the returning point (recording end or tape end), see “RETURN POINT” ( pg. 48).

●It is possible to use the Mode Lock function. ( pg. 17)

Manual Tracking

Your recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the PR buttons.

1Override automatic tracking.

During playback, press p on the remote control.

2Adjust the tracking manually.

Press PR + or – on the remote control.

●Press p again to return to automatic tracking.

NOTE:

When a new tape is inserted, the recorder enters the automatic tracking mode automatically.

Soundtrack Selection

Your recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.

During Playback

Pressing AUDIO changes the soundtrack as follows:

TRACK

USE

 

On-Screen Display

 

 

 

HI FI

For Hi-Fi stereo tapes

L j h R

 

 

 

HI FI

For main audio of Bilingual tapes

L j

 

 

 

HI FI

For sub audio of Bilingual tapes

h R

 

 

 

NORM

For audio-dubbed tapes

 

 

HI FI

For audio-dubbed tapes

NORM

 

 

 

NOTES:

●“HI FI L j h R” should normally be selected. In this mode, Hi-Fi stereo tapes are played back in stereo, and the normal audio track is played back automatically for tapes with only normal audio.

●For instructions on recording stereo and bilingual programmes, refer to page 22.

●“O.S.D. (PLAY)” must be set to “ON”, or the on-screen displays will not appear ( pg. 46).

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Connector cover Front ViewClose the battery cover until it clicks in place Rear ViewFront Display Panel ON-SCREEN Display Remote Control How To Use Operating JVC TVsSituate the recorder Check the contents10 EN Connect the recorder to TV8To connect to a TV with S-VIDEO/AUDIO in connectors Video ConnectionTurn on the recorder Auto Set Up12 EN Select your countryWith RF connection Perform Auto Set UpConfirm/Set video channel With AV or S-VIDEO connectionJust Clock Results of Auto Set Up appear on the front display panel14 EN Last-Function MemoryBasic Playback High-Speed Turbo Search 16 ENSlow Motion Pause during playbackIndex Search Mode Lock To prohibit any operations during playbackVariable Speed Search Skip SearchRepeat Playback 18 ENNext Function Memory Manual TrackingSet the tape speed Recording Resume FunctionChoose a programme Start recordingWatching Another Mode Lock To prohibit any operations during recording20 EN Accidental erasure preventionTape Remaining Time Repeat RecordingSuper VHS ET S-VHS ET Engage the S-VHS ET mode22 EN Receiving Stereo and Bilingual ProgrammesPlayback RecordingSR-V10E-1 Series Playback24 EN SR-V10E-2Make connections Turn on all componentsLoad cassettes Start playback Series Recording 26 ENPress 7on either of SR-V10E Set the input mode on both SR-V10EPrepare for recording Start recording Press 0on the SR-V10E which is recordingBefore performing the Showview Timer Programming Access the Showview screenAccess the Showview Program screen 28 ENEngage the recorder’s timer mode Set the VPS/PDC modeAccess the Title Edit screen Enter the programme titleExpress Timer Programming 30 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR+32 EN Enter the programme modeBefore performing the 24 Hour Express Timer Programming Set the programme start/stop time and channelReturn to the timer mode Cancel or change a programmeDisengage the timer mode Access the Programme Check screen/displaySelect the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenRecording mode Programme RecordingBefore performing the following steps Navigation 36 ENProgramme Navigation Screen Access the Main Menu screenNavigation Playback Load a recorded cassette38 EN Edit Programme TitleSelect the programme Delete the tape data Entering CharacterDelete Tape Data Example Enter JVC NewsEdit From a Camcorder 40 ENAdvantages of S-VHS video recorders Set the input mode of recording deckAnother Video Recorder Start the source playerConnecting To a Satellite Receiver Connecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingPicture reproduction is also linked to this function Using this video recorder as the source player for editingPowered back on We recommend that you set Digital TBC/NR to on whenScreen While timer-recording in SP mode46 EN Set PROG. Navigation to OFFSetting Correction to the luminance signal to enhance detailS-VHS recording mode is selected Panel. Then, set S-VHS to OFF. The S-VHS indicator goes off48 EN About Ntsc PlaybackGuide Program Number Set Showview System SetupAccess the Initial Set screen Guide Program Number50 EN Access the Auto Channel Set screenTuner Set Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK 52 EN Manual Channel SetSelect the item Delete a ChannelChange Station Channel Position Delete a channel54 EN Set Stations aSet Stations B TV Station And ID List Station NameAccess the Clock Set screen Clock Set56 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationVideo Channel Set 58 ENPower 60 EN RecordingOther Problems 62 EN PlaybackLines VHS Signal-to-noise ratio 45 dB Horizontal resolutionScan system Lines S-VHS64 EN Memo 66 EN
Top Page Image Contents