JVC SR-V10E Programme Recording, Recording mode, Before performing the following steps

Page 35

EN 35

Automatic Satellite

Programme

Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder’s AUDIO/VIDEO IN connectors and programme the timer on the satellite receiver. The recorder starts or stops recording by the signals input from the satellite receiver. After recording, the recorder’s power shuts off automatically.

““indicator

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver’s power is turned on.

●It is not possible to perform Automatic Satellite Programme Recording via S VIDEO IN connector. ( pg. 42)

●Automatic Satellite Programme Recording and timer-recording cannot be done at the same time.

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder’s AUDIO/VIDEO IN connectors. ( pg. 42)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place. If the tab has been removed, set “REC SAFETY” to “OFF” ( pg. 48).

A Set the tape speed.

Press SP/LP/EP (p).

●It is not possible to select EP mode if “COLOUR SYSTEM” is set to “MESECAM”. ( pg. 48)

B Engage the Automatic Satellite Programme

Recording mode.

Press and hold REC LINK for about 2 seconds. The ““ indicator lights up and the recorder turns off automatically.

NOTES:

●To disengage the Automatic Satellite Programme Recording mode, press REC LINK. The ““ indicator goes off.

●If the recorder’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.

●In step 2, if the ““ indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer Programming” ( pg. 30) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.

●The ““ indicator blinks while Automatic Satellite Programme Recording is in progress.

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

●Pressing the recorder’s 1 button while Automatic Satellite Programme Recording is in progress turns off the recorder’s power and disengages the Automatic Satellite Programme Recording mode.

●If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible to set different tape speeds for each programme.

●Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not

start Automatic Satellite Programme Recording even though the ““ indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer.

●The B.E.S.T. system ( pg. 23) does not work while Automatic Satellite Programme Recording is in progress.

●Just Clock ( pg. 56) does not work when the Automatic Satellite Programme Recording mode is engaged.

●When the Automatic Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Automatic Satellite

Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON” ( pg. 45).

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Close the battery cover until it clicks in placeFront Display Panel ON-SCREEN Display Remote Control Operating JVC TVs How To UseConnect the recorder to TV Check the contents10 EN Situate the recorderVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsSelect your country Auto Set Up12 EN Turn on the recorderWith AV or S-VIDEO connection Perform Auto Set UpConfirm/Set video channel With RF connectionLast-Function Memory Results of Auto Set Up appear on the front display panel14 EN Just ClockBasic Playback Pause during playback 16 ENSlow Motion High-Speed Turbo SearchSkip Search Mode Lock To prohibit any operations during playbackVariable Speed Search Index SearchManual Tracking 18 ENNext Function Memory Repeat PlaybackStart recording Recording Resume FunctionChoose a programme Set the tape speedAccidental erasure prevention Mode Lock To prohibit any operations during recording20 EN Watching AnotherRepeat Recording Tape Remaining TimeReceiving Stereo and Bilingual Programmes Engage the S-VHS ET mode22 EN Super VHS ET S-VHS ETRecording PlaybackSR-V10E-2 Series Playback24 EN SR-V10E-1Load cassettes Start playback Make connectionsTurn on all components 26 EN Series RecordingPress 0on the SR-V10E which is recording Set the input mode on both SR-V10EPrepare for recording Start recording Press 7on either of SR-V10E28 EN Access the Showview screenAccess the Showview Program screen Before performing the Showview Timer ProgrammingEnter the programme title Set the VPS/PDC modeAccess the Title Edit screen Engage the recorder’s timer mode30 EN Express Timer ProgrammingPress PR+ To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel positionSet the programme start/stop time and channel Enter the programme modeBefore performing the 24 Hour Express Timer Programming 32 ENAccess the Programme Check screen/display Cancel or change a programmeDisengage the timer mode Return to the timer modeOverlapping programmes blink on the TV screen Cancel or change programme settingConfirm the overlapping programmes Select the programme to modifyBefore performing the following steps Recording modeProgramme Recording 36 EN NavigationLoad a recorded cassette Access the Main Menu screenNavigation Playback Programme Navigation ScreenSelect the programme 38 ENEdit Programme Title Example Enter JVC News Entering CharacterDelete Tape Data Delete the tape data40 EN Edit From a CamcorderStart the source player Set the input mode of recording deckAnother Video Recorder Advantages of S-VHS video recordersConnecting To a Satellite Receiver Make connections Connecting/Using a Stereo SystemSelect the mode setting Mode SetAccess the Mode Set screen Select the modeWe recommend that you set Digital TBC/NR to on when Using this video recorder as the source player for editingPowered back on Picture reproduction is also linked to this functionSet PROG. Navigation to OFF While timer-recording in SP mode46 EN ScreenPanel. Then, set S-VHS to OFF. The S-VHS indicator goes off Correction to the luminance signal to enhance detailS-VHS recording mode is selected SettingAbout Ntsc Playback 48 ENGuide Program Number Showview System SetupAccess the Initial Set screen Guide Program Number SetAuto Channel Set Access the Auto Channel Set screenTuner Set 50 ENPress OK Perform Auto Channel SetView the Confirmation screen Manual Channel Set 52 ENDelete a channel Delete a ChannelChange Station Channel Position Select the itemSet Stations B 54 ENSet Stations a Station Name TV Station And ID List56 EN Access the Clock Set screenClock Set Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock data58 EN Video Channel SetPower Recording 60 ENOther Problems Playback 62 ENLines S-VHS Signal-to-noise ratio 45 dB Horizontal resolutionScan system Lines VHS64 EN Memo 66 EN
Top Page Image Contents