JVC SR-V10E specifications How To Use, Operating JVC TVs

Page 9

EN 9

Buttons with a small dot on the left side of the name can also be used to operate your JVC TV while holding down the TV button. ( “Operating JVC TVs” below)

This remote control transmits A code signals only; it is not applicable to B code signals.

How To Use

The remote control can operate most of your video recorder’s functions, as well as basic functions of JVC TV sets. ( “Operating JVC TVs” below)

●Point the remote control toward the receiving window.

●The maximum operating distance of the remote control is about 8 m.

Operating JVC TVs

To operate your TV, while holding down the TV button, press the corresponding button: 1, TV/VCR, TV PR +/–, TV %+/–,

^(TV Muting).

NOTES:

●When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover.

●Depending on the type of JVC TV, some or all functions may not be operated using the remote control.

●If the remote control doesn’t work properly, remove its batteries, wait a short time, replace the batteries and then try again.

Image 9

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Close the battery cover until it clicks in placeFront Display Panel ON-SCREEN Display Remote Control Operating JVC TVs How To Use10 EN Check the contentsSituate the recorder Connect the recorder to TVVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectors12 EN Auto Set UpTurn on the recorder Select your countryConfirm/Set video channel Perform Auto Set UpWith RF connection With AV or S-VIDEO connection14 EN Results of Auto Set Up appear on the front display panelJust Clock Last-Function MemoryBasic Playback Slow Motion 16 ENHigh-Speed Turbo Search Pause during playbackVariable Speed Search Mode Lock To prohibit any operations during playbackIndex Search Skip SearchNext Function Memory 18 ENRepeat Playback Manual TrackingChoose a programme Recording Resume FunctionSet the tape speed Start recording20 EN Mode Lock To prohibit any operations during recordingWatching Another Accidental erasure preventionRepeat Recording Tape Remaining Time22 EN Engage the S-VHS ET modeSuper VHS ET S-VHS ET Receiving Stereo and Bilingual ProgrammesRecording Playback24 EN Series PlaybackSR-V10E-1 SR-V10E-2Make connections Turn on all componentsLoad cassettes Start playback 26 EN Series RecordingPrepare for recording Start recording Set the input mode on both SR-V10EPress 7on either of SR-V10E Press 0on the SR-V10E which is recordingAccess the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 28 ENAccess the Title Edit screen Set the VPS/PDC modeEngage the recorder’s timer mode Enter the programme title30 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Before performing the 24 Hour Express Timer Programming Enter the programme mode32 EN Set the programme start/stop time and channelDisengage the timer mode Cancel or change a programmeReturn to the timer mode Access the Programme Check screen/displayConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Overlapping programmes blink on the TV screenRecording mode Programme RecordingBefore performing the following steps 36 EN NavigationNavigation Playback Access the Main Menu screenProgramme Navigation Screen Load a recorded cassette38 EN Edit Programme TitleSelect the programme Delete Tape Data Entering CharacterDelete the tape data Example Enter JVC News40 EN Edit From a CamcorderAnother Video Recorder Set the input mode of recording deckAdvantages of S-VHS video recorders Start the source playerConnecting To a Satellite Receiver Make connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingPowered back on Using this video recorder as the source player for editingPicture reproduction is also linked to this function We recommend that you set Digital TBC/NR to on when46 EN While timer-recording in SP modeScreen Set PROG. Navigation to OFFS-VHS recording mode is selected Correction to the luminance signal to enhance detailSetting Panel. Then, set S-VHS to OFF. The S-VHS indicator goes offAbout Ntsc Playback 48 ENAccess the Initial Set screen Showview System SetupGuide Program Number Set Guide Program NumberTuner Set Access the Auto Channel Set screen50 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK Manual Channel Set 52 ENChange Station Channel Position Delete a ChannelSelect the item Delete a channel54 EN Set Stations aSet Stations B Station Name TV Station And ID ListAccess the Clock Set screen Clock Set56 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operation58 EN Video Channel SetPower Recording 60 ENOther Problems Playback 62 ENScan system Signal-to-noise ratio 45 dB Horizontal resolutionLines VHS Lines S-VHS64 EN Memo 66 EN