JVC SR-V10E specifications Make connections, Turn on all components, Load cassettes Start playback

Page 25

EN 25

Using two sets of SR-V10E, you can play back two cassettes alternately as many times as you want. You can select the returning point for Series Playback.

NOTE:

Use the buttons and controls on the recorder for the Series Playback operations (except when using Mode Lock

( pg. 17)).

A Make connections.

Connect two sets of SR-V10E and a TV using AV cables as illustrated on page 24.

●The mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5 mm mini-plug connector.

●When playing back S-VHS recordings, it is recommended to use the S-VIDEO connection to obtain the high quality pictures.

B Turn on all components.

After completing the connections, turn on all the components.

●Set your TV to the VIDEO or AV mode. Refer to the TV instruction manual.

C Set the input mode on the SR-V10E-2.

Turn the JOG dial to the right or left on the SR-V10E-2 to select the appropriate input mode depending on the connectors being used.

“L-1”: for the rear AUDIO/VIDEO IN connectors

“F-1”: for the front AUDIO/VIDEO input connectors

“S-1”: for the rear AUDIO/S VIDEO IN connectors

“S-2”: for the front AUDIO/S-VIDEO input connectors

D Load cassettes.

E Start playback.

Press 4on either of SR-V10E.

●When the playback reaches to the returning point (tape end or recording end ( pg. 48)), the other SR-V10E successively starts playback. (The cassette will automatically be rewound when the playback stops.) Therefore, the cassettes loaded on two SR-V10E will be played back alternately as many times as you want.

F Stop playback.

Press 0on the SR-V10E which is playing back a cassette.

NOTES:

●If you do not want to display the operational indicators on the

TV screen during playback, set “O.S.D. (PLAY)“ and “O.S.D. (REC)“ to “OFF“ ( pg. 45, 46).

●If there is a power outage during Series Playback, the playback will resume automatically when the power is restored to the recorder if the lithium battery is not exhausted.

●It is possible to use the Mode Lock function ( pg. 17).

Insert the playback cassette into each SR-V10E.

Image 25

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Close the battery cover until it clicks in placeFront Display Panel ON-SCREEN Display Remote Control Operating JVC TVs How To Use10 EN Check the contentsSituate the recorder Connect the recorder to TVVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectors12 EN Auto Set UpTurn on the recorder Select your countryConfirm/Set video channel Perform Auto Set UpWith RF connection With AV or S-VIDEO connection14 EN Results of Auto Set Up appear on the front display panelJust Clock Last-Function MemoryBasic Playback Slow Motion 16 ENHigh-Speed Turbo Search Pause during playbackVariable Speed Search Mode Lock To prohibit any operations during playbackIndex Search Skip SearchNext Function Memory 18 ENRepeat Playback Manual TrackingChoose a programme Recording Resume FunctionSet the tape speed Start recording20 EN Mode Lock To prohibit any operations during recordingWatching Another Accidental erasure preventionRepeat Recording Tape Remaining Time22 EN Engage the S-VHS ET modeSuper VHS ET S-VHS ET Receiving Stereo and Bilingual ProgrammesRecording Playback24 EN Series PlaybackSR-V10E-1 SR-V10E-2Turn on all components Make connectionsLoad cassettes Start playback 26 EN Series RecordingPrepare for recording Start recording Set the input mode on both SR-V10EPress 7on either of SR-V10E Press 0on the SR-V10E which is recordingAccess the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 28 ENAccess the Title Edit screen Set the VPS/PDC modeEngage the recorder’s timer mode Enter the programme title30 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Before performing the 24 Hour Express Timer Programming Enter the programme mode32 EN Set the programme start/stop time and channelDisengage the timer mode Cancel or change a programmeReturn to the timer mode Access the Programme Check screen/displayConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Overlapping programmes blink on the TV screenProgramme Recording Recording modeBefore performing the following steps 36 EN NavigationNavigation Playback Access the Main Menu screenProgramme Navigation Screen Load a recorded cassetteEdit Programme Title 38 ENSelect the programme Delete Tape Data Entering CharacterDelete the tape data Example Enter JVC News40 EN Edit From a CamcorderAnother Video Recorder Set the input mode of recording deckAdvantages of S-VHS video recorders Start the source playerConnecting To a Satellite Receiver Make connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingPowered back on Using this video recorder as the source player for editingPicture reproduction is also linked to this function We recommend that you set Digital TBC/NR to on when46 EN While timer-recording in SP modeScreen Set PROG. Navigation to OFFS-VHS recording mode is selected Correction to the luminance signal to enhance detailSetting Panel. Then, set S-VHS to OFF. The S-VHS indicator goes offAbout Ntsc Playback 48 ENAccess the Initial Set screen Showview System SetupGuide Program Number Set Guide Program NumberTuner Set Access the Auto Channel Set screen50 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK Manual Channel Set 52 ENChange Station Channel Position Delete a ChannelSelect the item Delete a channelSet Stations a 54 ENSet Stations B Station Name TV Station And ID ListClock Set Access the Clock Set screen56 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operation58 EN Video Channel SetPower Recording 60 ENOther Problems Playback 62 ENScan system Signal-to-noise ratio 45 dB Horizontal resolutionLines VHS Lines S-VHS64 EN Memo 66 EN