JVC HR-IP820U instruction manual Consolidating Program Names, Uploading a Directory

HR-IP820U INDEX Plus+ 97.5.20 5:45 PM Page 23

6To view the directory of an RI tape later, insert the tape and press INDEX Plus+. The screen from step 1 appears. Press 2, then input the Tape Number. (Be careful not to input an incorrect Tape Number.)

NOTES:

●If the tape has been recorded over several times, Index Marks may remain and RE-INDEX/SCAN may not be successful. Erase the Index Marks manually (refer to pg. 20 of the HR-IP820U instruction manual.)

●If Retroactive Indexing is unsuccessful, "FAILURE" appears on screen in step 3. Re-perform the procedure from step 1.

●Retroactive Indexing may occasionally be unsuccessful, depending on the condition of the tape.

4The screen now looks like this:

Press F2 and then 1.

Using the DIGIT and CURSOR buttons (VOL +/–, REW, FF), input the program name.

-RESCANNED TAPE-￿
	TAPE#0012￿
>Program#001	30	SP￿
Program#002	200	EP
￿
￿
￿

PAGE01￿ (PLAY)(STOP) UTIL.￿MORE ￿ PRESS(INDEXPlus+)TO EXIT

		REVISE TITLE￿
>	￿	PORTS	#0012￿
SWALLOWS VS BAYS			30	SP￿
SUPER JAPAN CUP			200	EP￿
￿
￿
￿

PAGE01￿ ENT:STORE <<:TOP >>:END￿ UNDO INS DEL small

Consolidating Program Names

If the tape you want to index contains Index Marks in locations other than the start points of the programs, a "ghost" program may appear on the directory. If this should happen, consolidate the names according to the procedure that follows.

Procedure

1After step 3 on page 22 (under "Retroactive Indexing"), press CANCEL.

2 The next screen looks	-RESCANNED TAPE-￿
like this:			TAPE#0012￿
	>Program#001	30			SP￿
	Program#002	80			EP￿
	Program#003	120			EP ￿
	￿
	￿
			PAGE01￿
	(PLAY)(STOP)		UTIL.	MORE￿
	PRESS(INDEXPlus+)TO EXIT

Select the programs to be consolidated using the CURSOR button (VOL +/–). (If you're consolidating, for example, programs 2 and 3, place the cursor next

Press INDEX Plus+ and the normal screen reappears.

NOTE: If you consolidate programs that were recorded at different tape speeds (SP/EP), –– appears. The program time is calculated as though the program were recorded entirely in EP mode.

Uploading A Directory

You can load the directory of a tape which you previously removed from your library, or of a tape recorded on another INDEX Plus+ VCR, into your VCR's memory.

Preparation

1.Turn on the power to the TV and the VCR.

2.Set the TV to the channel or mode appropriate for video playback.

3.Insert the tape with the directory you want to load/reload.

to program 3.) Then press CLEAR.

3 A screen like this one	-RESCANNED TAPE-￿
appears:		TAPE#0012￿
	Program#001	30	SP￿
	Program#002	80	EP￿
	>Program#003	120	EP￿
	￿
	￿

PAGE01￿

Press F1.ENT:DELETE CANCEL:RETURN￿

COMBINE WITH UPPER PROG

Procedure

1Press INDEX Plus+. The screen to the right appears (if the library is empty, FIND is replaced by

RESTORE):

￿

￿

￿

DIRECTORY DOES NOT EXIST￿ IN THIS VCR￿

￿

￿

PRESS(ENTER)TO UPLOAD￿ PRESS(INDEXPlus+)TO EXIT￿

FIND

Press ENTER. If the tape was not at the beginning, the VCR automatically rewinds it to that point before starting its search for programs.

23