Dish Network Solo 111 manual Appendix a

Page 94

Appendix A

Warning: Tighten all the coaxial cable connections only by hand.

Using a wrench may over-tighten the connections, causing damage.

Such damage is not covered by the Limited Warranty.

2.Connect a coaxial cable from the TV SET OUT connection on your receiver to your television's RF tuner input. Peel off the white sticker and affix it to the cable close to where it connect to the TV SET OUT connection on the back of the receiver.

3.Plug in the receiver's power cord. Make sure both the receiver and TV are turned on.

4.You should see the Point Dish/Signal Strength menu in the new receiver. If you do not, open the Main Menu, by pressing MENU fol- lowed by 6-1-1on the remote.

5.Select Check Switch. Select Test to run Check Switch.

6.When Check Switch is complete, you will see an Installation Sum- mary screen. If the screen shows the correct switch and the message "Satellite reception verified" for all satellites in your system, go to step 7. If the Installation Summary screen does not detect all of the satellites your system should be receiving, check and retighten (by hand) the cable connections between your receiver, LNBFs and switches in your system. Then press Test to rerun Check Switch again.

7.Select OK to return to the Point Dish/Signal Strength screen. Then select Cancel to exit the Point Dish/Signal Strength screen.

8.An Attention screen will open asking if the mounting and positioning of your dish is complete with a "Locked" indication in the Point Dish/Signal Strength screen. Since your system is already installed and your dish is pointed for the strongest possible signal strength, you can select Yes.

9.The receiver will begin taking a software upgrade. You will see the message shown below.

A progress bar at the bottom of the screen will show how the software upgrade is progressing. Once the software upgrade is complete, you will see a second message that the receiver's memory is now being programmed.

This message may disappear, your screen may go blank for a few minutes, and the green light may continue to blink. This is normal and does not indicate a problem with the receiver.

10.When the software upgrade is complete, press VIEW TV and you should now be able to watch TV programming. To activate your pro- gramming on this newly installed receiver, call 1-800-333-DISH (3474). See Chapter 1, Introduction.

Page 84

Image 94

Contents Contents Contents Important Safety Instructions Safety Welcome to Dish Networktm OverviewIf YOU Need More Assistance Quick Start GuideFinding Programs To Watch Satellite Signal QualityAbout Satellite Television Solar Interference Parts of the System Receiver Front PanelParts of the System Receiver Back PanelRemote Control Remote ControlPress the Power button to turn the receiver on or OFF Select Save Left Arrow Menus MenusMain Menu Favorites Lists Menu Timers Menu Browse Banner Browse BannerChapter Using the Menus Changing ChannelsUsing the System Using the Menus Using the Program Guide Using the Program Guide Program GuideUsing the Program Banner Using the Browse BannerUsing the Browse Banner Ordering PAY PER View Programs At the confirmation menuUsing Themes Using ThemesUsing Search Chapter Using Favorites Lists Using Favorites ListsMaking a Favorites List Active Using Timers Using TimersEvent Timer Frequencies Select the Create option to save the event timer Overlapping Event Timers Editing AN Event Timer Deleting AN Event Timer Setting Up the Receiver to Control the VCR Number PAD buttonsUsing Locks Using Locks Creating or Changing Rating Content Code Locks Creating or Changing Channel Locks Unlocking the Receiver To unlock pay per view programs To hide adult channels Opening a Locked ITEM, or Opening the Locks Menu Using Caller ID Using Caller ID Restarting the Receiver Resetting the Receiver to Factory SettingsChanging Program Languages Testing the Phone Connection Testing the Phone ConnectionSetting UP the Receiver for Channel 3 or Installation Instructions Chapter Finding the SatellitesInstalling a Dish 500 Antenna Mounting the Dish No YESInstalling a Dish 500 Antenna Attach the Lnbf to the Y-bracket using the two Lnbf screws Installing a Dish 500 Antenna Chapter Installing a Dish 500 Antenna Installing a Multiple Dish DishPro System Installing a Dish 500 Antenna DishPro Wiring Diagrams Dish 500, One DishPro Twin LNBF, Two DishPro ReceiversDishPro Wiring Diagrams Dish 500, One DishPro Quad LNBF, Four DishPro ReceiversChapter For four Chapter DishPro Wiring Diagrams Chapter Running Coaxial Cable Connecting the Receiver to a Phone Line Connecting the Receiver to a Phone Line Chapter Troubleshooting Tables ReferenceReference Troubleshooting Tables Dishpro Twin Lnbf What Is Possible Reason What to Do Happening Hearing a Program Using the Menus Changing Channels Buying a PAY PER View Program Using Event Timers VCR Codes Device CodesSBR Index Index Index Index Appendix a Appendix a Appendix a Appendix a What the Warranty Covers What the Warranty Does Not CoverLegal Limitations If You Need AssistanceAdvance Exchange Program Accessory WarrantyPost Receipt Exchange Program Residential Customer Agreement Residential Customer Agreement Billing Policies and Payments for Services Cancellation of Service Leased Equipment Limitation of OUR Liability Staying Legal Telephone CommunicationFCC Compliance Radio InterferenceAppendix B