Kathrein MSK 25 manual Example LNB14,0V 22kHz 150mA, Press 2nF LNB

Page 25

SAT measurement

Example

✐

LNB:14,0V 22kHz 150mA

Note

☞

Activating the 22 kHz signal:

Press [2nF] [LNB] [8]

LC display:

•LNB voltage: 14 V

•Power consumption: 150 mA

•22 kHz signal activated

By pressing [8] again, the 22 kHz signal can be deactivated.

By calling up a different function, e. g. [2ndF] [CH-FRQ] or 2x [2ndF], the LNB menu will be closed automatically.

Image 25

Contents MSK 25 Satellite/TV/FM Test Receiver analogue/digital Preface Contents Mpeg Picture Representation option in DVB-C or DVB-T option Safety Rules Signs and SymbolsGeneral Information Additionally included in DeliveryPage Qpsk Overview of FunctionsQAM CofdmLNB 0/5 20 SAT Technical DataDVB-S-MER1 Control Elements Control Elements and IndicatorsConnections right hand side TFT Colour ScreenSAT/DVB-S TV/DVB-C/*DVB-T Short Cut OverviewRF Input Socket ConnectionsExternal DC Voltage Supply Scart OutputSwitching-Off Switching-UpCommissioning Software Accu −−−−− LEV 48.5dBuVFactory Setting on Delivery Setup-MenuSetup Menu Setting Setup Menu Call-UpBattery Operation Mains Operation and Battery OperationMains Operation Standard Change-Over SAT measurement2ndF STD Press 2ndF STDSAT Menu Frequency Entry Frequency Display and Frequency EntryExample FR1508.0MHz LEV 86.5dBuVSAT DVB-S Level Measurement SAT Analogue Level MeasurementLevel Overflow and Level Underflow Locating Satellites Calling up Scan mode Press 2ndF ScanScan Menu LEV-Range2 SAT Example 2ndF 2ndF ExitBearing Menu LEV-Range2 SAT Example Bearing for Individual Reception FrequenciesPress 2ndF Level Press 2ndF SC SAT Analogue Sound Carrier FrequencyBwnarrow Mpeg Picture Representation option in DVB-S DVB-S MER, BER and Offset MeasurementCalling up DVB-S measurement MER12.6dB MHz BER1.7e-7Press 2ndF LNB LNB Voltage and 22 kHz/60 Hz Change-OverPress 2nF LNB Example LNB14,0V 22kHz 150mAOr + DiSEqC Digital Satellite Equipment ControlPress 2ndF SAT-CTRL Framing Byte MenuHEX Hex Byte Description Address Byte MenuCommand Byte Menu SAT measurement Data Byte Menu Simple Tone Burst DiSEqC2ndF SAT-CTRL 2ndF 2ndFBis TV measurement=ANALOG 3=DVBT DVB-C/DVB-T Change-Over Channel display and channel entry TV Channel Setting Menu Example CHS.11 LEV 62,5dBuVChanging over to special channel Press ./S 1Then press 1 7 5 ./S 2 5 Enter TV Frequency Entry Mode Example CH175,25 LEV 65,0dBuVTV/DVB-C/DVB-T Level Measurement Level Measurement TV AnalogueLEV.dBuV LEV.dBuVLEV-RANGE2 TV Bearing MenuTT1 TT2 Sound Carrier Distance and Sound Carrier Level2ndF SC Example SC 5.85 MHz BER=2.145E-05 Nicam Sound Bit Error Rate MeasurementMpeg Picture Representation option in DVB-C or DVB-T option DVB-C/DVB-T option, MER, BER and Offset MeasurementMER30.5dB MHz BER2.0e-8 Calling up DVB-C/DVB-T option measurementFrequency Indication and Frequency Entry FM measurementFM Frequency Entry Menu Example LEV 65.0dBuV Then press 9 9 ./S 2 5 EnterFr104.80MHz LEV 86.5dBuV Level MeasurementFR104.80MHz LEV .dBuV FR104,80MHz LEV¯¯¯.¯dBuV LEV-RANGE2 FM SAT Spectrum Spectrum MeasurementTV Spectrum SAT-FullTV Spectrum Menu TV-Full FM SpectrumVHF UHF TV-NarrowChanging the Battery MaintenanceCustomer Service Technical Appendix Signal-to-Noise-Ratio+14.1 dB Instruction Set for 9xx Kathrein Matrix Production Run DiSEqC Commands for Kathrein MatricesInstruction Set for EXR 20 Kathrein Matrix Instruction Set for EXR 22 Kathrein MatrixVRF-CCIR URF-CCIR Channel TablesVHF UHF III Technical Appendix Technical Appendix Technical Appendix Technical Appendix 936.2642/D/1005/ZWT Subject to technical modifications