Kathrein MSK 25 manual General Information, Signs and Symbols, Safety Rules, Key

Page 5

General Information

Signs and Symbols

À

[key]

This user manual has been compiled for persons with some electrical engineering ability and knowledge. Users who have already operated similar measuring instruments can obtain the necessary commands for each operating step from the overview. In addition, the following examples will help you understand each operating step.

Always adhere to the instructions classified with the warning signal carefully, as otherwise the MSK 25 test receiver may be damaged or even be destroyed.

This symbol provides information on measuring functions and refers to chapters containing further particulars on a subject.

This symbol is followed by an example of the measuring function explained.

Find an overview of the commands for the germane short cut for the particular measuring function.

Key on the instrument to be pressed.

Safety Rules

Careful observance of the VDE safety instructions is essential!

Only fuses with the same power-down characteristics are to be used!

On feeding in signals, heed the allowable peak levels!

HF input: max. 120 dBµV (60 dBmV)!

Do not connect direct-current (DC) voltage to the RF socket!

Do not connect low frequency alternating-current (AC) voltage to the RF socket!

The instrument is also energised when disconnected! Use only the power supply unit provided for voltage feed!

Depending on the programming, between 5 V and 20 V may be connected to the RF input socket. From 10 V to 20 V, up to 500 mA can be obtained from the source, and up to 100 mA can be obtained from 5 V to 9.9 V.

Additionally included in Delivery

1 Wall power supply

1 BNC measuring cable

1 Adapter BNC socket – F socket

1 Adapter BNC socket – F plug

1 Adapter BNC socket – IEC socket

1 Adapter BNC socket – IEC plug

1 20 dB attenuation plug with d.c. voltage passage

(Find indications on the frequency response of the enclosed attenuation plug on the last page)

Electronic equipment is not household waste - in accordance with directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of 27th January 2003 on used electrical and electronic equipment, it must be disposed of properly.

At the end of its service life, take this unit for disposal at a relevant of. cial collection point.

5

Image 5
Contents MSK 25 Satellite/TV/FM Test Receiver analogue/digital Preface Contents Mpeg Picture Representation option in DVB-C or DVB-T option Safety Rules Signs and SymbolsGeneral Information Additionally included in DeliveryPage Qpsk Overview of FunctionsQAM CofdmLNB 0/5 20 SAT Technical DataDVB-S-MER1 Control Elements Control Elements and IndicatorsConnections right hand side TFT Colour ScreenSAT/DVB-S TV/DVB-C/*DVB-T Short Cut OverviewRF Input Socket ConnectionsExternal DC Voltage Supply Scart OutputSwitching-Off Switching-UpCommissioning Software Accu −−−−− LEV 48.5dBuVFactory Setting on Delivery Setup-MenuSetup Menu Setting Setup Menu Call-UpMains Operation Mains Operation and Battery OperationBattery Operation Standard Change-Over SAT measurement2ndF STD Press 2ndF STDSAT Menu Frequency Entry Frequency Display and Frequency EntryExample FR1508.0MHz LEV 86.5dBuVLevel Overflow and Level Underflow SAT Analogue Level MeasurementSAT DVB-S Level Measurement Locating Satellites Calling up Scan mode Press 2ndF ScanScan Menu LEV-Range2 SAT Example 2ndF 2ndF ExitPress 2ndF Level Bearing for Individual Reception FrequenciesBearing Menu LEV-Range2 SAT Example Bwnarrow SAT Analogue Sound Carrier FrequencyPress 2ndF SC Mpeg Picture Representation option in DVB-S DVB-S MER, BER and Offset MeasurementCalling up DVB-S measurement MER12.6dB MHz BER1.7e-7Press 2ndF LNB LNB Voltage and 22 kHz/60 Hz Change-OverPress 2nF LNB Example LNB14,0V 22kHz 150mAOr + DiSEqC Digital Satellite Equipment ControlHEX Framing Byte MenuPress 2ndF SAT-CTRL Hex Byte Description Address Byte MenuCommand Byte Menu SAT measurement Data Byte Menu Simple Tone Burst DiSEqC2ndF SAT-CTRL 2ndF 2ndF=ANALOG 3=DVBT TV measurementBis DVB-C/DVB-T Change-Over Channel display and channel entry TV Channel Setting Menu Example CHS.11 LEV 62,5dBuVChanging over to special channel Press ./S 1Then press 1 7 5 ./S 2 5 Enter TV Frequency Entry Mode Example CH175,25 LEV 65,0dBuVTV/DVB-C/DVB-T Level Measurement Level Measurement TV AnalogueLEV.dBuV LEV.dBuVLEV-RANGE2 TV Bearing Menu2ndF SC Sound Carrier Distance and Sound Carrier LevelTT1 TT2 Example SC 5.85 MHz BER=2.145E-05 Nicam Sound Bit Error Rate MeasurementMpeg Picture Representation option in DVB-C or DVB-T option DVB-C/DVB-T option, MER, BER and Offset MeasurementMER30.5dB MHz BER2.0e-8 Calling up DVB-C/DVB-T option measurementFrequency Indication and Frequency Entry FM measurementFM Frequency Entry Menu Example LEV 65.0dBuV Then press 9 9 ./S 2 5 EnterFR104.80MHz LEV .dBuV FR104,80MHz LEV¯¯¯.¯dBuV Level MeasurementFr104.80MHz LEV 86.5dBuV LEV-RANGE2 FM SAT Spectrum Spectrum MeasurementTV Spectrum SAT-FullTV Spectrum Menu TV-Full FM SpectrumVHF UHF TV-NarrowCustomer Service MaintenanceChanging the Battery +14.1 dB Signal-to-Noise-RatioTechnical Appendix Instruction Set for 9xx Kathrein Matrix Production Run DiSEqC Commands for Kathrein MatricesInstruction Set for EXR 20 Kathrein Matrix Instruction Set for EXR 22 Kathrein MatrixVRF-CCIR URF-CCIR Channel TablesVHF UHF III Technical Appendix Technical Appendix Technical Appendix Technical Appendix 936.2642/D/1005/ZWT Subject to technical modifications