Kathrein UFS 902 manual Safety Instructions Important Information

Page 6

SAFETY INSTRUCTIONS - IMPORTANT INFORMATION

GB

DANGER!

WARNING!

Safety Instructions – Important Information

This page contains important information about the operation, installation location and connection of the unit. Read these instructions carefully before starting to use the unit.

Mains cable

Make sure that the mains cable (power supply cable) is not damaged. Units with a damaged mains cable must be disconnected from the mains (disconnect mains connector) and repaired by a qualified engineer before setup. Only use the power pack supplied (if available)!

Risk of death due to electric shock!

Cleaning

Disconnect the mains connector before cleaning the unit. Only use a dry cloth for cleaning and only clean the outer surface. Never open the unit.

Touching the parts inside the unit carries a risk of death due to electric shock!

Playing children

Make sure that children do not push any objects into the ventilation slots.

Risk of death due to electric shock!

Earth connection

The antenna system must be earthed as specified or equipotentially bonded. EN 60728/11 and any national regulations must be complied with.

Danger due to surge voltages, lightning strikes!

Mains voltage

Only operate the unit with the specified mains voltage (marked on the rear of the-unit or on the external power pack)! The unit may only be connected to the mains and turned on once it has been connected to the antenna and to the TV set or the cable network and PC.

If the mains voltage is too high, there is a risk of fire!

Repairs

Ensure that any repairs to your unit are carried out by qualified personnel. Opening the unit and attempting to repair it yourself voids all warranty claims!

Improper work on the unit can jeopardise the electrical safety of the unit.

The manufacturer accepts no liability for accidents caused by the user opening the unit!

Connections

Incorrect wiring of the connections can lead to malfunctions or defects on the unit!

CAUTION! Long periods of absence/storms/accessibility of the mains connector

Always turn off the unit at the mains switch if you will be absent for a long time or there is a storm. Disconnect it from the mains by unplugging the mains connector. This also applies to the other equipment connected to the unit. Isolation from the cable network is also recommended. Note any timer programs (receiver) and turn the unit on again promptly before the recording time. Ensure the mains connector is accessible at all times.

Installation location

All electronic equipment generates heat. However, the heating of this unit lies within the permissible range. Sensitive furniture surfaces and veneers may become discoloured by the effects of constant heat over time. The feet of the unit can also cause colour changes to treated furniture surfaces. If necessary, place the unit on a suitable stable and flat base!

Ventilation

The heat generated in this unit is adequately dissipated. However, the unit should never be installed in a cupboard or on shelves with inadequate ventilation. Never cover the cooling slots on the unit (e.g. with other equipment, magazines, tablecloths or curtains)!

Do not place any objects on top of the unit and maintain a clearance of at least 10 cm above the unit, so that the heat generated can be dissipated with no obstructions.

Moisture, sunlight, heat, naked flames

Protect the unit against moisture, dripping and splashed water (do not place any filled objects such as vases on top of the unit). Do not place the unit close to a heater or expose it to direct sunlight and do not operate it in damp locations. Only use the unit in a moderate climate, not in tropical conditions! Do not expose the unit to any naked flame, such as from a candle! This constitutes a fire hazard!

6

Image 6
Contents Hdtv receiver For satellite reception UFS Recording Function from Software Version Switching the Receiver OFFFOREWORD/IMPORTANT Information Information on Audio Mpeg INC. and S.I.SV.EL, S.P.ADisposal Instructions Used batteries are special wasteUpdate time cannot be changed Receiver FEATURES/PRODUCT PackageSwitching OFF the Receiver and Updating the EPG Product PackageContents Safety Instructions Important Information Safety Instructions Important InformationCONTROLS, Displays and Connections View of Front Panel Flap Folded DownView of Rear Panel Reception System Presets Connection and SetupConnecting the Unit SAT if Connections Reception RequirementsAudio Connection Inserting Batteries in the Remote ControlTV Connection OPTICAL/ELECTRICAL Digital OutputRemote Control  ... Remote Control RC Set-up using menuManual set-up not possible on UFS First Installation TV-Scart-Output SCARTor TV aspect ratioPicture format HDMI/YUV FormatSystem Number of Satellites Satellite and PositionLNB Type Test transponderFirst Installation LNB only First Installation LNB only First Installation One Cable Configure satellitesFirst Installation One Cable First Installation Single-cable system automatic First Installation Single-cable system manual Selection user-definedFirst Installation Single-cable system manual First Installation Single-cable system manual First Installation Single-cable system manual First Installation Single-cable system manual Channel Search Mode Execute Channel searchNetwork Search First Installation Channel Search Update time onLocal time offset UTC Operating Instructions Menu ConceptMain menu Menu TreeAlphanumeric Entries Language Selection OSDProgramme Information ON-SCREEN Displays OSDChannel Osds TV Channel OSDOpening Media Selection TV, Radio Opening Options ChannelError Message Option SelectionChannel List TV/RADIO Selection and sorting options Search functionEPG Electronic Programme Guide Opening the EPGCurrent View Selection optionsPreview View Programme Magazine Categories View Search Function Additional Information i Button Reminder Function Change Over to ProgrammeRecording Timer Programme present in the EPGProgramme not present in the EPG Recording Once only Recording DailyRecording Weekly Record USER-DEFINEDSeries Recording Timer List View Common Interface Important InformationInserting the Smartcard and the CA Module Common Interface Teletext Editing Channel List Selection of the LIST/CHANNEL to be EditedEditing LIST/CHANNELS Deleting Channels Last Function MemoryMoving Channels Skipping ChannelsLocking Channels Copying Channels to the Favourite ListStarting Block Marking Marking Several Channels Remove from favoritelist Editing Favourite ListsRemoving from Favourite List Rename favoritelistRenaming Favourite List Searching for Channels Channel Search Automatic Channel SearchSatellite Manual Channel Search Symbol Rate Transponder FrequencyPolarisation Channel Search with Service ID Searching for Channels Channel Search Locking Main Menu Setting a NEW Code PINParental Control Locking ReceiverSettings TV Settings Scart HDMI/YUVFunctions Audio Delay setting not currently availableCustomising Screen Menu Auto Dolby Digital OutputChannel OSD Duration Display Volume BARAdjust Menu on TV Front Display BrightnessDate and Time Antenna ConfigurationAutomatic time setting Common InterfaceService Menu Software UpdateUpdating software Updating channel listFactory Reset Remote Control Code USB Device ManagementStand-by button Backup OperationOperating from the Front Panel TV/R buttonFeatures Technical AppendixType UFS 902si UFS 902sw VHS/S-VHS Switching Scart Socket AssignmentConnection Example EXR 501/551/552 UAS EXU Short Technical Glossary HD Ready Hdcp High-bandwidth Digital Content ProtectionEb/No ratio Hdmi High Definition Multimedia InterfaceOSD On-Screen Display Qpsk Quadrature Phase Shift KeyingSAT if signal Pay TVStand-by Timer functionSmartcard Time-shift functionSubject Index Additional Information i ButtonReminder Function Change Over to Programme Problem Cause Remedy TroubleshootingService 936.3352/B/1108/ZWT Technical data subject to change