Kathrein UFS 902 manual USB Device Management, Remote Control Code

Page 71

SERVICE MENU

USB DEVICE MANAGEMENT

This function is not currently supported/activated.

REMOTE CONTROL CODE

Select the “Service” menu using the menu button , the  buttons on the main menu and .

Use the  buttons to switch to “Remote Control Code” and to open press the  button. The following display appears:

You can now use the remote control for your receiver to set a new remote control code. Simultaneously press buttons

+  +  for remote control code 1 (standard setting)

+  +  for remote control code 2

+  +  for remote control code 3

+  + for remote control code 4

After changing the remote control code you must now set your remote control to the code you selected. For this, simultaneously press buttons

+  for remote control code 1

+  for remote control code 2

+  for remote control code 3

+ for remote control code 4

Then press the  button. If the receiver display does not close down, the receiver and the remote control are not set to the same remote control code. Check your settings again.

71

Image 71
Contents Hdtv receiver For satellite reception UFS Information on Audio Mpeg INC. and S.I.SV.EL, S.P.A Switching the Receiver OFFFOREWORD/IMPORTANT Information Recording Function from Software VersionUsed batteries are special waste Disposal InstructionsProduct Package Receiver FEATURES/PRODUCT PackageSwitching OFF the Receiver and Updating the EPG Update time cannot be changedContents Safety Instructions Important Information Safety Instructions Important InformationView of Rear Panel CONTROLS, Displays and ConnectionsView of Front Panel Flap Folded Down Reception Requirements Connection and SetupConnecting the Unit SAT if Connections Reception System PresetsOPTICAL/ELECTRICAL Digital Output Inserting Batteries in the Remote ControlTV Connection Audio Connection ...  Remote ControlManual set-up not possible on UFS Remote Control RCSet-up using menu First Installation HDMI/YUV Format SCARTor TV aspect ratioPicture format TV-Scart-OutputSystem Satellite and Position Number of SatellitesTest transponder LNB TypeFirst Installation LNB only First Installation LNB only Configure satellites First Installation One CableFirst Installation One Cable First Installation Single-cable system automatic Selection user-defined First Installation Single-cable system manualFirst Installation Single-cable system manual First Installation Single-cable system manual First Installation Single-cable system manual First Installation Single-cable system manual Network Search Channel Search ModeExecute Channel search Local time offset UTC First Installation Channel SearchUpdate time on Menu Concept Operating InstructionsMenu Tree Main menuLanguage Selection OSD Alphanumeric EntriesTV Channel OSD ON-SCREEN Displays OSDChannel Osds Programme InformationOpening Options Channel Opening Media Selection TV, RadioChannel List TV/RADIO Error MessageOption Selection Search function Selection and sorting optionsOpening the EPG EPG Electronic Programme GuideSelection options Current ViewPreview View Programme Magazine Categories View Search Function Reminder Function Change Over to Programme Additional Information i ButtonProgramme not present in the EPG Recording TimerProgramme present in the EPG Recording Daily Recording Once onlyRecord USER-DEFINED Recording WeeklySeries Recording Timer List View Inserting the Smartcard and the CA Module Common InterfaceImportant Information Common Interface Teletext Selection of the LIST/CHANNEL to be Edited Editing Channel ListEditing LIST/CHANNELS Skipping Channels Last Function MemoryMoving Channels Deleting ChannelsStarting Block Marking Marking Several Channels Locking ChannelsCopying Channels to the Favourite List Rename favoritelist Editing Favourite ListsRemoving from Favourite List Remove from favoritelistRenaming Favourite List Automatic Channel Search Searching for Channels Channel SearchSatellite Manual Channel Search Polarisation Symbol RateTransponder Frequency Channel Search with Service ID Searching for Channels Channel Search Locking Receiver Setting a NEW Code PINParental Control Locking Main MenuSettings Scart HDMI/YUV TV SettingsAuto Dolby Digital Output Audio Delay setting not currently availableCustomising Screen Menu FunctionsFront Display Brightness Display Volume BARAdjust Menu on TV Channel OSD DurationCommon Interface Antenna ConfigurationAutomatic time setting Date and TimeSoftware Update Service MenuUpdating channel list Updating softwareFactory Reset USB Device Management Remote Control CodeTV/R button Backup OperationOperating from the Front Panel Stand-by buttonTechnical Appendix FeaturesType UFS 902si UFS 902sw Scart Socket Assignment VHS/S-VHS SwitchingConnection Example EXR 501/551/552 UAS EXU Short Technical Glossary Hdmi High Definition Multimedia Interface Hdcp High-bandwidth Digital Content ProtectionEb/No ratio HD ReadyPay TV Qpsk Quadrature Phase Shift KeyingSAT if signal OSD On-Screen DisplayTime-shift function Timer functionSmartcard Stand-byAdditional Information i Button Subject IndexReminder Function Change Over to Programme Troubleshooting Problem Cause RemedyService 936.3352/B/1108/ZWT Technical data subject to change