Toshiba KV-7960A instruction manual Contents of Screen Display

Page 14

INTRODUCTION

CONTENTS OF SCREEN DISPLAY

The normal MENU screen provides six menus after the initial screen for clock setting. Each MENU screen is shown below.

Press the DISPLAY button for a MENU screen. The menu is selected by pressing the SHIFT button. Then press the SET button to proceed to the next screen. Use the SHIFT button and the SET button for settings and adjustments in the same manner. To return to the initial screen press the DISPLAY button.

	Monitor Screen (initial screen)
PREPARATION
	1/ 1/95 SUN
	0:00:00 A 2

MENU Screen (initial screen)

M E N U

CLOCK SET

SETUP

DISPLAY MODE

TIME DATE SEARCH

END=[DISPLAY]

CLOCK SET Screen

CLOCK SET
(DAYLIGHT
SAVING TIME)	OUT

(MONTH) (DAY) (YEAR) 1 / 1 / '95

SUN (TIME) 0:00

MENU=[DISPLAY]

Comment

iSetting of clock. Unless the date-time is adjusted, the “PROGRAM” and “ALARM RECALL” will not appear on the MENU screen.

	Monitor Screen (normal screen)
RECORDING OPERATION
	8/28/96	WED
	17:30:02	A 2

MENU Screen (normal screen)

M E N U

CLOCK ADJUST

SETUP

DISPLAY MODE

PROGRAM

ALARM RECALL

TIME DATE SEARCH

END=[DISPLAY]

CLOCK ADJUST Screen

CLOCK ADJUST
(DAYLIGHT
SAVING TIME)	IN

(MONTH) (DAY) (YEAR)

8/ 28 / '96

WED

(TIME) 17:30

MENU=[DISPLAY]

iCorrection of date-time.

	PLAYBACK OPERATION
	NOTICE
	NOTICE

M E N U

CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH

END=[DISPLAY]

M E N U

CLOCK ADJUST

SETUP

DISPLAY MODE

PROGRAM ALARM RECALL TIME DATE SEARCH

END=[DISPLAY]

SETUP Screen

S E T U P
ALARM REC TIME	15S
SPEED	A 2H
1SHOT REC FIELD	1F
INTERVAL 0.2S
RESTART REC	OFF
TAPE END MODE	STOP
ALARM	STOP

MENU=[DISPLAY]

DISPLAY Screen

DISPLAY
(DATE)	ON
(DAY OF THE WEEK)	ON
(TIME)	ON
(SPEED)	ON
(VCR)	OFF
(ALARM)	ON
(12H/24H)	24H
(CHAR.LINES)	6

MENU=[DISPLAY]

iSetting of alarm recording mode (recording time, recording mode)

iSetting of One-Shot recording mode (number of recording fields, recording intervals).

iSetting of recording for restoration of power following a power failure.

iSetting of operation after detection of tape end (tape end detection mode for tape end detection during recording and when an alarm recording is made).

i Setting of display screen (date, day of week, time, recording time, VCR number, alarm).

iSetting of time display (24H, 12H).

13

Image 14

Contents Instruction Manual Important Precautions Please ReadPower-Cord Protection Important Safety InstructionsPower Sources Radiators, heat registers, stovesWhen the power-supply cord or plug is damaged AccessoriesPower Lines To restore the product to its normal operationFeatures Table of ContentsInstructions in Brief Front PanelCassette Compartment Time Mode / SET + buttonsTape Remain button Display buttonRear Panel Installation Word on the Exclusive 3N-100AAS Battery PackSpecification of Battery RemovalVCR Display Press to start play back 1PAUSE/STILL buttonREW button FF buttonConnections Connection with a Video CameraTo REC TRIGG. OUT Typical Connection with the Sequential SwitcherVideo OutputContents of Screen Display Alarm Recall Screen Setting the Clock OperationMonitor screen VCR display ON-SCREEN FunctionsDate-Time Display On-Screen PositionDisplay Screen Changes to the alarm number Alarm numberIs pressed. When an alarm is This function enables to indicate and record informationCounter Memory Alarm MemoryCounter Displays Code Number Condition of Abnormality Error MessageTape Remain A18 20s Fields/s Possible Continuous Virtual Real Time mode Setting the RECORDING/PLAYBACK TimeHOW to Operate 24 Hour Virtual Real Time Mode Unloading a Cassette Loading and Unloading a Video CassetteLoading a cassette Recording Camera and monitor TV Not been removedRestart REC Setting the Restart RecordingRestart Recording Daily Timer Recording Timer RecordingSetting the Timer Program Program ScreenTo cancel the timer recording, press the Power button or Press the Timer buttonPower goes off and the Timer display lights VCR display Button twice to erasePress the Shift Button to blink the MO1 start time Weekly Timer RecordingPress the Shift ButtonGRAM.to blink PRO FR2 Overlapping ProgramsExample DLYAlarm Recall Display Alarm RecordingOperation at Alarm Input Event RecordingConnecting the Alarm Terminals Cont Setting the Alarm RecordingDisplay Recording time ManualOperation of One-shot Recording Connecting the One-shot terminalONE-SHOT Recording Display Recording fieldsTo release the One-shot Recording mode Operation After Tape END Detection How to Set to Stop at End of TapeSetting contents Buzzer Screen display Counter display Display Operation after detection of tape endPress the + or SET How to Set to Auto Rewind at End of TapeAlarm recording does not operate during auto-rewind Menu ScreenHow to Set to Repeat Record at End of Tape ButtonREC. to select REW →Timing for Camera Switching Recording with the Sequential SwitcherConnection with the Sequential Switcher C D a B C DButton to set the REC REC Trigger Output Selection in the Alarm RecordingRecord mode Trigger SELPlayback Tracking AdjustmentRecording time mode Time mode for playback Picture Using the Shuttle DialREW Stop Search PlayPlayback in Various Modes Press the SET button to Set the Minute to Time Date SearchSearch Operation Alarm Search Still picture mode Press the Play buttonSignal Levels of INPUT/OUTPUT Terminals Input/Output Terminal Signal level Additional remarksA2-hour mode 10want to set to Check the playback picture recorded in A2 hour modePress Time Mode button to go to Daily and Periodic InspectionRequest for Periodic Checks Recording Usage frequency Time modeSteps to Take after Daily Checks Tape Usage FrequencyDew Condensation Function/Operation Before Calling Service PersonnelInstallation RecordingPlayback Other mattersAccessories SpecificationsConnector section Warranty card Dew caution sheetToshiba America C.P.INC