Toshiba KV-7960A Word on the Exclusive 3N-100AAS Battery Pack, Specification of Battery, Removal

Page 9

A Word on the Exclusive 3N-100AAS Battery Pack

The nickel-cadmium battery pack (3N-100AAS) is used for power source of the built-in clock and memory circuit.

Charging the Battery Pack

1.Turn on the power of the VCR.

2.The battery pack in the VCR is charged.

Battery Installation

Removal:

1.Remove the battery cover.

2.Disconnect the connector in the VCR.

RED wire

Connector

Battery pack

Installation:

1.Install the battery pack placing the red wire upside, and connect the connector on the battery pack to this VCR. Make sure the polarities (+) and (–) are correct.

2.Close the battery cover.

Note:

If the Battery Pack is removed, the memory data will be erased. In such a case, perform the setting from the first step.

Specification of Battery

i	Temperature
	For charging	:	0°C to 80°C
	For operating	:	–20°C to 80°C
	For storing	:	–30°C to 80°C
i	Charging time	:	more than 48 hours

Notes:

iUse only for this VCR.

iDo not dispose of the batteries into fire.

iDo not short circuit the terminals.

iDo not modify or disassemble.

iAvoid dropping, unnecessary shocks.

INTRODUCTION

PREPARATION

RECORDING

OPERATION

PLAYBACK

OPERATION

NOTICE

8

Image 9

Contents Instruction Manual Please Read Important PrecautionsPower Sources Important Safety InstructionsPower-Cord Protection Radiators, heat registers, stovesPower Lines AccessoriesWhen the power-supply cord or plug is damaged To restore the product to its normal operationTable of Contents FeaturesFront Panel Instructions in BriefTape Remain button Time Mode / SET + buttonsCassette Compartment Display buttonRear Panel Specification of Battery Word on the Exclusive 3N-100AAS Battery PackInstallation RemovalVCR Display REW button 1PAUSE/STILL buttonPress to start play back FF buttonConnection with a Video Camera ConnectionsVideo Typical Connection with the Sequential SwitcherTo REC TRIGG. OUT OutputContents of Screen Display Alarm Recall Screen Operation Setting the ClockDate-Time Display ON-SCREEN FunctionsMonitor screen VCR display On-Screen PositionDisplay Screen Is pressed. When an alarm is Alarm numberChanges to the alarm number This function enables to indicate and record informationAlarm Memory Counter DisplaysCounter Memory Error Message Tape RemainCode Number Condition of Abnormality Setting the RECORDING/PLAYBACK Time HOW to Operate 24 Hour Virtual Real Time ModeA18 20s Fields/s Possible Continuous Virtual Real Time mode Loading and Unloading a Video Cassette Loading a cassetteUnloading a Cassette Camera and monitor TV Not been removed RecordingSetting the Restart Recording Restart RecordingRestart REC Setting the Timer Program Timer RecordingDaily Timer Recording Program ScreenPower goes off and the Timer display lights VCR display Press the Timer buttonTo cancel the timer recording, press the Power button or Button twice to eraseWeekly Timer Recording Press the Shift ButtonGRAM.to blink PROPress the Shift Button to blink the MO1 start time Example Overlapping ProgramsFR2 DLYOperation at Alarm Input Alarm RecordingAlarm Recall Display Event RecordingConnecting the Alarm Terminals Display Recording time Setting the Alarm RecordingCont ManualONE-SHOT Recording Connecting the One-shot terminalOperation of One-shot Recording Display Recording fieldsTo release the One-shot Recording mode Setting contents Buzzer Screen display Counter display How to Set to Stop at End of TapeOperation After Tape END Detection Display Operation after detection of tape endAlarm recording does not operate during auto-rewind How to Set to Auto Rewind at End of TapePress the + or SET Menu ScreenButtonREC. to select REW → How to Set to Repeat Record at End of TapeConnection with the Sequential Switcher Recording with the Sequential SwitcherTiming for Camera Switching C D a B C DRecord mode REC Trigger Output Selection in the Alarm RecordingButton to set the REC Trigger SELTracking Adjustment Recording time mode Time mode for playbackPlayback REW Stop Using the Shuttle DialPicture Search PlayPlayback in Various Modes Time Date Search Search OperationPress the SET button to Set the Minute to Still picture mode Press the Play button Alarm SearchInput/Output Terminal Signal level Additional remarks Signal Levels of INPUT/OUTPUT TerminalsPress Time Mode button to go to Check the playback picture recorded in A2 hour modeA2-hour mode 10want to set to Daily and Periodic InspectionSteps to Take after Daily Checks Recording Usage frequency Time modeRequest for Periodic Checks Tape Usage FrequencyDew Condensation Installation Before Calling Service PersonnelFunction/Operation RecordingOther matters PlaybackConnector section SpecificationsAccessories Warranty card Dew caution sheetToshiba America C.P.INC