Toshiba KV-7960A ONE-SHOT Recording, Operation of One-shot Recording, Display Recording fields

Page 33

ONE-SHOT RECORDING

It is possible with this VCR to carry out one-shot recording to record only when there is a trigger input from outside or for use as a data file. If a trigger is input to the one-shot input on the back, there will be recording for the field numbers set at the time interval set.

INTRODUCTION

Connecting the One-shot terminal

To One-shot in

To GND

Consult with your dealer about the remote control switch.

Example: When setting for a total of four fields at an interval of 0.5 seconds.

4-fields recording

0.5sec

one field recording

PREPARATION

Operation of One-shot Recording

Press the TIME MODE button to select L01, L02 or

1 L03.

H

Press the SHIFT button to make 1 SHOT REC

4 FIELD blink and press the + SET button to set the number of recording fields.

–TIME MODE + SET

DISPLAY – TIME MODE + SET

S E T U P
ALARM REC TIME	15S
SPEED	A 2H
1SHOT REC FIELD	1F
INTERVAL	0.2S
RESTART REC	OFF

SHIFT

TRACKING

TAPE END MODE	STOP
ALARM	STOP

LOCATION SELECT

Press the DISPLAY

2 button.

DISPLAY – TIME MODE +

SET

SHIFT	TRACKING
SHIFT
	LOCATION SELECT

M E N U

CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH

END=[DISPLAY]

MENU=[DISPLAY]

iEach time pressing the + SET button the display changes

as follows.

1F → 2F → 4F → 8F → 16F → 32F → MANUAL

iEach time pressing the – SET button, the display changes in the reverse direction.

Press the SHIFT

3 button to make SETUP blink and press the + SET button.

DISPLAY – TIME MODE +

SET

M E N U

CLOCK ADJUST SETUP

DISPLAY MODE PROGRAM ALARM RECALL

Display	Recording fields
1F	1 field

2F	2 fields

4F	4 fields

8F	8 fields

16F	16 fields

SHIFT

TRACKING

TIME DATE SEARCH

32F	32 fields
MANUAL	Accepting the one-

LOCATION SELECT

END=[DISPLAY]

shot input.

Note:

iBecause the head is constantly tracing the same location, it can cause damage to the head and tape. For this reason, if there is no one-shot input when the time mode is set to L01, L02 or L03 the VCR automatically records 2 fields every 1, 2 or 3 minutes to protect the tape and heads. Choose the time mode suited to your particular purpose.

PLAYBACK

OPERATION

NOTICE

32

Image 33

Contents Instruction Manual Please Read Important PrecautionsPower Sources Important Safety InstructionsPower-Cord Protection Radiators, heat registers, stovesPower Lines AccessoriesWhen the power-supply cord or plug is damaged To restore the product to its normal operationTable of Contents FeaturesFront Panel Instructions in BriefTape Remain button Time Mode / SET + buttonsCassette Compartment Display buttonRear Panel Specification of Battery Word on the Exclusive 3N-100AAS Battery PackInstallation RemovalVCR Display REW button 1PAUSE/STILL buttonPress to start play back FF buttonConnection with a Video Camera ConnectionsVideo Typical Connection with the Sequential SwitcherTo REC TRIGG. OUT OutputContents of Screen Display Alarm Recall Screen Operation Setting the ClockDate-Time Display ON-SCREEN FunctionsMonitor screen VCR display On-Screen PositionDisplay Screen Is pressed. When an alarm is Alarm numberChanges to the alarm number This function enables to indicate and record informationAlarm Memory Counter DisplaysCounter Memory Error Message Tape RemainCode Number Condition of Abnormality Setting the RECORDING/PLAYBACK Time HOW to Operate 24 Hour Virtual Real Time ModeA18 20s Fields/s Possible Continuous Virtual Real Time mode Loading and Unloading a Video Cassette Loading a cassetteUnloading a Cassette Camera and monitor TV Not been removed RecordingSetting the Restart Recording Restart RecordingRestart REC Setting the Timer Program Timer RecordingDaily Timer Recording Program ScreenPower goes off and the Timer display lights VCR display Press the Timer buttonTo cancel the timer recording, press the Power button or Button twice to eraseWeekly Timer Recording Press the Shift ButtonGRAM.to blink PROPress the Shift Button to blink the MO1 start time Example Overlapping ProgramsFR2 DLYOperation at Alarm Input Alarm RecordingAlarm Recall Display Event RecordingConnecting the Alarm Terminals Display Recording time Setting the Alarm RecordingCont ManualONE-SHOT Recording Connecting the One-shot terminalOperation of One-shot Recording Display Recording fieldsTo release the One-shot Recording mode Setting contents Buzzer Screen display Counter display How to Set to Stop at End of TapeOperation After Tape END Detection Display Operation after detection of tape endAlarm recording does not operate during auto-rewind How to Set to Auto Rewind at End of TapePress the + or SET Menu ScreenButtonREC. to select REW → How to Set to Repeat Record at End of TapeConnection with the Sequential Switcher Recording with the Sequential SwitcherTiming for Camera Switching C D a B C DRecord mode REC Trigger Output Selection in the Alarm RecordingButton to set the REC Trigger SELTracking Adjustment Recording time mode Time mode for playbackPlayback REW Stop Using the Shuttle DialPicture Search PlayPlayback in Various Modes Time Date Search Search OperationPress the SET button to Set the Minute to Still picture mode Press the Play button Alarm SearchInput/Output Terminal Signal level Additional remarks Signal Levels of INPUT/OUTPUT TerminalsPress Time Mode button to go to Check the playback picture recorded in A2 hour modeA2-hour mode 10want to set to Daily and Periodic InspectionSteps to Take after Daily Checks Recording Usage frequency Time modeRequest for Periodic Checks Tape Usage FrequencyDew Condensation Installation Before Calling Service PersonnelFunction/Operation RecordingOther matters PlaybackConnector section SpecificationsAccessories Warranty card Dew caution sheetToshiba America C.P.INC