Toshiba KV-7960A Alarm Recording, Operation at Alarm Input, Event Recording, Alarm Recall Display

Page 30

PREPARATIONINTRODUCTION

ALARM RECORDING

If an alarm condition arises, the alarm function operates with an alarm input signal.

Operation at Alarm Input

When there is an alarm during recording, recording pause or stop modes, the VCR automatically goes into alarm recording mode. The VCR can be programmed to record in the following time modes during alarm recording: A2, A6, A12, A18, A24.

Alarm input

 

 

 

Recording

A2, A6, A12, A18,

Recording

Recording pause

Recording pause

A24 hours

Stop

Stop

 

 

Alarm Recording

 

iWhen there is an alarm input in the STOP mode, a slight delay will occur in start of the alarm recording.

iWhen the pause mode continues for 10 minutes the VCR goes to the stop mode. This occurs in order to protect the video heads and tape. While in pause mode, the video head is constantly tracing the same location.

iAlarm recording will not operate from power off mode and timer power off mode.

RECORDING

OPERATION

 

 

PLAYBACK

OPERATION

 

 

Event Recording

If event recording is desired, set the VCR’s recording mode to L01, L02 or L03. In order to accomplish this press the time mode button until “L01”, “L02” or “L03” is shown.

If there is no alarm input present when in “L01”, “L02” or “L03” mode, the VCR automatically forwards 2 fields with recording every appointed time (L01: 1min, L02: 2min, L03: 3min.) to protect the tape and the video head from damage.

Warning at Alarm Recording

When an alarm signal is input, the buzzer sounds and the alarm display on the VCR DISPLAY lights.

Alarm display lights and then blinks when alarm recording is finished.

 

ALARM

H

 

 

 

 

 

 

REC

SP

 

 

 

 

 

 

 

 

 

 

 

The day of the week display

 

 

 

 

changes to the alarm number

 

Changes to a display of A2, A6, A12, A18 or A24.

8/28/96 A01

during alarm recording.

 

 

 

 

 

17:30:13 A 2

Changes to a display of A2,

• Turn off the BUZZER switch to stop the buzzer.

 

 

A6, A12, A18 or A24.

•To stop the alarm display blinking, press the ALARM button to change the counter display to the alarm counter and then press the RESET button.

Alarm Recall Display

Check the alarm input information on the ALARM RECALL screen.

NOTICE

M E N U

CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH

END=[DISPLAY]

 

 

 

 

 

 

ALARM RECALL

 

 

AL1

8/19/96MON 20:35:09

 

AL2

8/ 7/96WED 21:35:16

 

AL3

7/25/96THU 0:14:12

 

AL4

7/12/96FRI 19:14:12

 

AL5

6/20/96THU 23:14:10

 

AL6

4/ 1/96MON 21:07:13

 

AL7 --/--/----- --:--:--

 

1ST

4/ 1/96MON 21:07:13

 

 

MENU=[DISPLAY]

 

 

 

 

•At 1ST, the first (oldest) alarm input information is displayed.

•At AL1, the latest alarm input information is displayed.

•When more than seven items are input, the old information is erased and the new information is stored in the memory.

•To erase the alarm recall contents, press the ALARM button to change the counter display to alarm counter and press the

29 RESET button.

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Instruction Manual Important Precautions Please ReadPower-Cord Protection Important Safety InstructionsPower Sources Radiators, heat registers, stovesWhen the power-supply cord or plug is damaged AccessoriesPower Lines To restore the product to its normal operationFeatures Table of ContentsInstructions in Brief Front PanelCassette Compartment Time Mode / SET + buttonsTape Remain button Display buttonRear Panel Installation Word on the Exclusive 3N-100AAS Battery PackSpecification of Battery RemovalVCR Display Press to start play back 1PAUSE/STILL buttonREW button FF buttonConnections Connection with a Video CameraTo REC TRIGG. OUT Typical Connection with the Sequential SwitcherVideo OutputContents of Screen Display Alarm Recall Screen Setting the Clock OperationMonitor screen VCR display ON-SCREEN FunctionsDate-Time Display On-Screen PositionDisplay Screen Changes to the alarm number Alarm numberIs pressed. When an alarm is This function enables to indicate and record informationAlarm Memory Counter DisplaysCounter Memory Error Message Tape RemainCode Number Condition of Abnormality Setting the RECORDING/PLAYBACK Time HOW to Operate 24 Hour Virtual Real Time ModeA18 20s Fields/s Possible Continuous Virtual Real Time mode Loading and Unloading a Video Cassette Loading a cassetteUnloading a Cassette Recording Camera and monitor TV Not been removedSetting the Restart Recording Restart RecordingRestart REC Daily Timer Recording Timer RecordingSetting the Timer Program Program ScreenTo cancel the timer recording, press the Power button or Press the Timer buttonPower goes off and the Timer display lights VCR display Button twice to eraseWeekly Timer Recording Press the Shift ButtonGRAM.to blink PROPress the Shift Button to blink the MO1 start time FR2 Overlapping ProgramsExample DLYAlarm Recall Display Alarm RecordingOperation at Alarm Input Event RecordingConnecting the Alarm Terminals Cont Setting the Alarm RecordingDisplay Recording time ManualOperation of One-shot Recording Connecting the One-shot terminalONE-SHOT Recording Display Recording fieldsTo release the One-shot Recording mode Operation After Tape END Detection How to Set to Stop at End of TapeSetting contents Buzzer Screen display Counter display Display Operation after detection of tape endPress the + or SET How to Set to Auto Rewind at End of TapeAlarm recording does not operate during auto-rewind Menu ScreenHow to Set to Repeat Record at End of Tape ButtonREC. to select REW →Timing for Camera Switching Recording with the Sequential SwitcherConnection with the Sequential Switcher C D a B C DButton to set the REC REC Trigger Output Selection in the Alarm RecordingRecord mode Trigger SELTracking Adjustment Recording time mode Time mode for playbackPlayback Picture Using the Shuttle DialREW Stop Search PlayPlayback in Various Modes Time Date Search Search OperationPress the SET button to Set the Minute to Alarm Search Still picture mode Press the Play buttonSignal Levels of INPUT/OUTPUT Terminals Input/Output Terminal Signal level Additional remarksA2-hour mode 10want to set to Check the playback picture recorded in A2 hour modePress Time Mode button to go to Daily and Periodic InspectionRequest for Periodic Checks Recording Usage frequency Time modeSteps to Take after Daily Checks Tape Usage FrequencyDew Condensation Function/Operation Before Calling Service PersonnelInstallation RecordingPlayback Other mattersAccessories SpecificationsConnector section Warranty card Dew caution sheetToshiba America C.P.INC
Top Page Image Contents