Toshiba KV-7960A instruction manual Signal Levels of INPUT/OUTPUT Terminals

Page 45

NOTICE

SIGNAL LEVELS OF INPUT/OUTPUT TERMINALS

Input/Output Terminal	Signal level	Additional remarks
	Open			DC5V
				DC5V
ALARM IN	Ground input		10K	10K
			10K
		100	10K
	0V – 0.5V	100	10K
	0V – 0.5V	IN
		IN
	200 ms or greater	GND	0.001μ	10K
	200 ms or greater		0.001μ	10K
	Open			DC5V
			10K	10K
	Ground input		10K
ALARM RESET	Ground input	100	10K
	0V – 0.5V	RESET
		GND	0.001μ	10K
	200 ms or greater		0.001μ	10K
	200 ms or greater

		Alarm recording	DC5V
			220
ALARM OUT		5V output	OUT
ALARM OUT		5V output	10
		Output impedance	GND
	0V	Output impedance
	0V	230 Ohm : MAX 10mA
		230 Ohm : MAX 10mA

	5V				DC5V
	a: 20 ms				2.2K
	a: 20 ms				OUT
REC TRIGG. OUT	(A2, A6)				OUT
REC TRIGG. OUT	(A2, A6)	0V		Output impedance	220
	a: 32 ms	0V			GND
	a: 32 ms
	(A12, A18, A24, 24~)			220 Ohm : MAX 10mA
	(A12, A18, A24, 24~)		a	220 Ohm : MAX 10mA
	(See page 38.)		a
	(See page 38.)

Open	Tape end
	TAPE END
TAPE END OUT	220
	GND

	Short	Output impedance
		220 Ohm : MAX 20mA
	approx. 2 seconds.
	Open				DC5V
ONE SHOT IN				10K	10K
				10K
	Ground input		100	10K
	0V – 0.5V		IN
	0V – 0.5V
			GND	0.001μ	10K
		200 ms or greater		0.001μ	10K
		200 ms or greater

INTRODUCTION

PREPARATION

RECORDING

OPERATION

PLAYBACK

OPERATION

NOTICE

Image 45

Contents Instruction Manual Please Read Important PrecautionsPower Sources Important Safety InstructionsPower-Cord Protection Radiators, heat registers, stovesPower Lines AccessoriesWhen the power-supply cord or plug is damaged To restore the product to its normal operationTable of Contents FeaturesFront Panel Instructions in BriefTape Remain button Time Mode / SET + buttonsCassette Compartment Display buttonRear Panel Specification of Battery Word on the Exclusive 3N-100AAS Battery PackInstallation RemovalVCR Display REW button 1PAUSE/STILL buttonPress to start play back FF buttonConnection with a Video Camera ConnectionsVideo Typical Connection with the Sequential SwitcherTo REC TRIGG. OUT OutputContents of Screen Display Alarm Recall Screen Operation Setting the ClockDate-Time Display ON-SCREEN FunctionsMonitor screen VCR display On-Screen PositionDisplay Screen Is pressed. When an alarm is Alarm numberChanges to the alarm number This function enables to indicate and record informationAlarm Memory Counter DisplaysCounter Memory Error Message Tape RemainCode Number Condition of Abnormality Setting the RECORDING/PLAYBACK Time HOW to Operate 24 Hour Virtual Real Time ModeA18 20s Fields/s Possible Continuous Virtual Real Time mode Loading and Unloading a Video Cassette Loading a cassetteUnloading a Cassette Camera and monitor TV Not been removed RecordingSetting the Restart Recording Restart RecordingRestart REC Setting the Timer Program Timer RecordingDaily Timer Recording Program ScreenPower goes off and the Timer display lights VCR display Press the Timer buttonTo cancel the timer recording, press the Power button or Button twice to eraseWeekly Timer Recording Press the Shift ButtonGRAM.to blink PROPress the Shift Button to blink the MO1 start time Example Overlapping ProgramsFR2 DLYOperation at Alarm Input Alarm RecordingAlarm Recall Display Event RecordingConnecting the Alarm Terminals Display Recording time Setting the Alarm RecordingCont ManualONE-SHOT Recording Connecting the One-shot terminalOperation of One-shot Recording Display Recording fieldsTo release the One-shot Recording mode Setting contents Buzzer Screen display Counter display How to Set to Stop at End of TapeOperation After Tape END Detection Display Operation after detection of tape endAlarm recording does not operate during auto-rewind How to Set to Auto Rewind at End of TapePress the + or SET Menu ScreenButtonREC. to select REW → How to Set to Repeat Record at End of TapeConnection with the Sequential Switcher Recording with the Sequential SwitcherTiming for Camera Switching C D a B C DRecord mode REC Trigger Output Selection in the Alarm RecordingButton to set the REC Trigger SELTracking Adjustment Recording time mode Time mode for playbackPlayback REW Stop Using the Shuttle DialPicture Search PlayPlayback in Various Modes Time Date Search Search OperationPress the SET button to Set the Minute to Still picture mode Press the Play button Alarm SearchInput/Output Terminal Signal level Additional remarks Signal Levels of INPUT/OUTPUT TerminalsPress Time Mode button to go to Check the playback picture recorded in A2 hour modeA2-hour mode 10want to set to Daily and Periodic InspectionSteps to Take after Daily Checks Recording Usage frequency Time modeRequest for Periodic Checks Tape Usage FrequencyDew Condensation Installation Before Calling Service PersonnelFunction/Operation RecordingOther matters PlaybackConnector section SpecificationsAccessories Warranty card Dew caution sheetToshiba America C.P.INC