Toshiba KV-7960A instruction manual Rear Panel

Page 8

INTRODUCTION

Rear Panel

PREPARATION

OPTION BOX cover

4

5

6

 

 

ALL CLEAR

 

 

 

 

IN

GND

ALARM

RESET

 

 

 

OUT

 

GND

ONE SHOT

IN

 

 

 

GND

.

REC TRIGG

OUT

 

TAPE END

SEE MANUAL

3

13

1

2

7

9

10 BATTERY cover

REMOTE IN

MIC IN

IN VIDEO OUT

AUDIO

SEE MANUAL

8 11 12

RECORDING

OPERATION

 

 

PLAYBACK

OPERATION

 

 

NOTICE

1TAPE END OUT terminal

Signal output terminal to annunciate to other devices that the tape has run out on the VCR.

2REC TRIGGER OUT terminal

Signal output terminal to control the switching interval of the video cameras when connected to a sequential switcher or multiplexer.

3ALARM OUT terminal

Output terminal to transmit an alarm signal to peripheral equipment.

4ALARM RESET terminal

Input terminal to reset alarm recording.

Alarm recording is reset when this terminal is connected to the ground terminal during recording.

5ALARM IN terminal

Input terminal to start alarm recording.

The VCR goes into alarm recording mode when this terminal is connected to the ground terminal while in the record mode, record pause mode, or stop mode.

6ALL CLEAR button

Pressing this button will clear the entire time-date, and timer program memory. The power will be turned off at the same time. Pressing the POWER button will restore power.

7REMOTE IN jack

Input jack for optional wired remote control.

8MIC IN jack

Input jack for audio signals from a microphone. The RCA jack input (audio input) is automatically switched off when this jack is utilized.

9VIDEO IN connector (BNC)

Input connector for video signal. Connect with an external video source such as a video camera, etc.

pVIDEO OUT connector (BNC)

Output connector for video signal. Connect with a monitor TV.

qAUDIO IN jack (RCA type)

Input jack for audio signal. Connect with an external audio source.

wAUDIO OUT jack (RCA type)

Output jack for audio signal. Connect with an external audio equipment.

eONE SHOT IN terminal

Input terminal to start one shot recording.

The VCR goes into one shot recording mode when this terminal is connected to the ground terminal while in the L01, L02 or L03 record mode.

Notes:

•ALL CLEAR button

Do not use this function (ALL CLEAR) frequently. Press this button only when an abnormality (ex. VCR display does not turn ON.) occurs.

When this button is pressed, the power turns OFF and each data stored (ex. clock, timer program, etc.) is cleared and returns to the initial setting status. It will be necessary to re-program the VCR after turning the unit on again.

•OPTION BOX cover

This VCR provides an optional port for connecting an optional module to the rear of the unit.

If you would like additional information regarding the available options for this VCR please consult your dealer. The installation of the optional module should be per- formed only by qualified technical personnel.

7

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Instruction Manual Important Precautions Please ReadImportant Safety Instructions Power SourcesPower-Cord Protection Radiators, heat registers, stovesAccessories Power LinesWhen the power-supply cord or plug is damaged To restore the product to its normal operationFeatures Table of ContentsInstructions in Brief Front PanelTime Mode / SET + buttons Tape Remain buttonCassette Compartment Display buttonRear Panel Word on the Exclusive 3N-100AAS Battery Pack Specification of BatteryInstallation RemovalVCR Display 1PAUSE/STILL button REW buttonPress to start play back FF buttonConnections Connection with a Video CameraTypical Connection with the Sequential Switcher VideoTo REC TRIGG. OUT OutputContents of Screen Display Alarm Recall Screen Setting the Clock OperationON-SCREEN Functions Date-Time DisplayMonitor screen VCR display On-Screen PositionDisplay Screen Alarm number Is pressed. When an alarm isChanges to the alarm number This function enables to indicate and record informationCounter Memory Alarm MemoryCounter Displays Code Number Condition of Abnormality Error MessageTape Remain A18 20s Fields/s Possible Continuous Virtual Real Time mode Setting the RECORDING/PLAYBACK TimeHOW to Operate 24 Hour Virtual Real Time Mode Unloading a Cassette Loading and Unloading a Video CassetteLoading a cassette Recording Camera and monitor TV Not been removedRestart REC Setting the Restart RecordingRestart Recording Timer Recording Setting the Timer ProgramDaily Timer Recording Program ScreenPress the Timer button Power goes off and the Timer display lights VCR displayTo cancel the timer recording, press the Power button or Button twice to erasePress the Shift Button to blink the MO1 start time Weekly Timer RecordingPress the Shift ButtonGRAM.to blink PRO Overlapping Programs ExampleFR2 DLYAlarm Recording Operation at Alarm InputAlarm Recall Display Event RecordingConnecting the Alarm Terminals Setting the Alarm Recording Display Recording timeCont ManualConnecting the One-shot terminal ONE-SHOT RecordingOperation of One-shot Recording Display Recording fieldsTo release the One-shot Recording mode How to Set to Stop at End of Tape Setting contents Buzzer Screen display Counter displayOperation After Tape END Detection Display Operation after detection of tape endHow to Set to Auto Rewind at End of Tape Alarm recording does not operate during auto-rewindPress the + or SET Menu ScreenHow to Set to Repeat Record at End of Tape ButtonREC. to select REW →Recording with the Sequential Switcher Connection with the Sequential SwitcherTiming for Camera Switching C D a B C DREC Trigger Output Selection in the Alarm Recording Record modeButton to set the REC Trigger SELPlayback Tracking AdjustmentRecording time mode Time mode for playback Using the Shuttle Dial REW StopPicture Search PlayPlayback in Various Modes Press the SET button to Set the Minute to Time Date SearchSearch Operation Alarm Search Still picture mode Press the Play buttonSignal Levels of INPUT/OUTPUT Terminals Input/Output Terminal Signal level Additional remarksCheck the playback picture recorded in A2 hour mode Press Time Mode button to go toA2-hour mode 10want to set to Daily and Periodic InspectionRecording Usage frequency Time mode Steps to Take after Daily ChecksRequest for Periodic Checks Tape Usage FrequencyDew Condensation Before Calling Service Personnel InstallationFunction/Operation RecordingPlayback Other mattersSpecifications Connector sectionAccessories Warranty card Dew caution sheetToshiba America C.P.INC
Top Page Image Contents