InFocus 560, 570 manual Setting Up the LitePro, Image Size measured diagonally

Page 13

Setting Up the LitePro

This chapter describes how to position the LitePro projector for optimum viewing and how to connect it to your equipment.

1.If you are setting up the LitePro for the first time, you’ll need to install the two projection lamps that were shipped with it. Refer to ”Replacing the Projection Lamps” on page 40 for instructions.

2.Place the projector on a flat surface.

If you want to use the LitePro’s Rear Project feature, set it up behind your translucent screen. Refer to “Rear Projection” on page 28 for more information.

The projector must be within 6 feet of your power source.

The projector must be within 6 feet of the computer.

The distance from the LitePro’s lens to the screen determines the size of the projected image as shown below.

8 ft. (2.4m)

6 ft. (1.8m)

5 ft. (1.5m)

5.7 ft. (1.7m)

9.9 ft. (3m) 7.2 ft. (2.2m)

Distance to Screen

(measured parallel to tabletop)

elevated about 2” (5cm) from table

Figure 2. Image Size (measured diagonally)

LitePro 560/570 User’s Guide

5

Image 13
Contents LCD Projector Users Guide Fold and tear here Page Page Certifications Declaration of Conformity Contents Power Source Safety SummaryPower Cord Do not look into the lensFuse GroundingLamp Hot SurfacesNot shown IntroductionCables and Adapters CompatibilityUsage Guidelines Remote Control Programmer KitIf You Need Assistance Image Size measured diagonally Setting Up the LiteProConnecting the LCD end of the LitePro cable Connecting an IBM-compatible desktop computer Connecting a Macintosh desktop computer Connecting an IBM-compatible laptop computer Connecting a Macintosh PowerBook Connecting a Composite Video Cable Connecting an S-Video Cable Connecting the Audio from a Video Player Connecting an external speaker Connecting a microphone Setting Up the LitePro Basic Image Adjustment Using the LiteProUsing the Remote Control Turning the LitePro OffAdjusting the Height Focusing the ImageSwitching to the Spare Lamp Switching to the Spare LampMenu Using the Remote Control ButtonsSelect/enter Arrow buttonsNext Prev VolumeMute MicStandby ProgMenu Using the MenusHighlighting Menu Functions Audio MenuMaking Changes to Menu Functions Menu 1 Functions Resetting Menu Functions to the Default SettingsRemoving the Menu from the Screen BrightnessUp/Down SyncLeft/Right Rear Projection Menu 2 FunctionsSource Prompt RS-232 Test PatternAuto Standby Ntsc ResetPalette Source EnableProg Button Tracking LanguageVideo Type Text Mode and Pixel SliceSharpness CompAudio Menu Functions Volume and Audio LockTreble BassBalance and Fade Loudness Cleaning the Lens MaintenanceReplacing the Projection Lamps Opening the Lamp Door Bulb Guard Replacing Batteries in the Remote ControlReplacing the Fuse Installing New BatteriesLocating the Fuse Removing the Fuse Holder Before You Call for Assistance TroubleshootingProblem Nothing on screen Solutions to Common ProblemsProblem Color or VGA text not being projected Problem Only the test pattern is displayed Problem Image is not centered on the screenProblem Image is too wide or narrow for screen Problem Image is out of focusProblem LitePro displays vertical lines, bleeding or spots Problem Image and menus are reversed left to rightProblem Image is noisy or streaked Problem Projected colors don’t match the monitor’s colorsAppendix SpecificationsAppendix Accessories LCD Connector Cable Connector Pin AssignmentsGND Monitor and VGA ConnectorsAST Laptop Display Activation ChartFN-F1 Appendix Assistance, see Technical Support audio IndexLite show button 22 LitePro Quadra, see Macintosh Index Limited Warranty 010-0060-05 USA