InFocus 570, 560 manual Using the Menus

Page 32

Using the LitePro

Using the Menus

The LitePro has three menus: Menu 1, Menu 2, and the Audio Menu.

Menu 1

Menu 1 allows you to adjust the brightness, tint, synchronization (sync), and display positioning. Each of the these menu settings is described in “Menu 1 Functions” starting on page 26.

To display Menu 1:

Press the menu button on the remote.

Figure 15. Menu 1

If you see “EEPROM Failed” displayed on Menu 1, one of the integrated circuits inside the LitePro has failed. The LitePro will continue to operate normally. The only loss of functionality is that changes you make in the menus will not be saved after you turn the LitePro off. All settings will return to their defaults. Call In Focus Technical Support. Refer to “If You Need Assistance” on page 3 for the phone number.

Menu 2

Menu 2 contains controls for a variety of functions that you probably won’t need to change very often. Each of these is described later in this manual in “Menu 2 Functions” starting on page 28.

To display Menu 2:

1.Press the menu button on the remote to display Menu 1.

2.Press the left or right arrow buttons until “Menu 2” is high- lighted.

3.Press select/enter.

24

LitePro 560/570 User’s Guide

Image 32
Contents LCD Projector Users Guide Fold and tear here Page Page Certifications Declaration of Conformity Contents Safety Summary Power SourcePower Cord Do not look into the lensGrounding FuseLamp Hot SurfacesIntroduction Not shownCompatibility Cables and AdaptersIf You Need Assistance Remote Control Programmer KitUsage Guidelines Setting Up the LitePro Image Size measured diagonallyConnecting the LCD end of the LitePro cable Connecting an IBM-compatible desktop computer Connecting a Macintosh desktop computer Connecting an IBM-compatible laptop computer Connecting a Macintosh PowerBook Connecting a Composite Video Cable Connecting an S-Video Cable Connecting the Audio from a Video Player Connecting an external speaker Connecting a microphone Setting Up the LitePro Using the LitePro Basic Image AdjustmentUsing the Remote Control Turning the LitePro OffFocusing the Image Adjusting the HeightSwitching to the Spare Lamp Switching to the Spare LampUsing the Remote Control Buttons MenuNext Arrow buttonsSelect/enter Volume PrevMute MicProg StandbyUsing the Menus MenuMaking Changes to Menu Functions Audio MenuHighlighting Menu Functions Resetting Menu Functions to the Default Settings Menu 1 FunctionsRemoving the Menu from the Screen BrightnessLeft/Right SyncUp/Down Source Prompt Menu 2 FunctionsRear Projection Auto Standby Test PatternRS-232 Reset NtscSource Enable PaletteProg Button Language TrackingText Mode and Pixel Slice Video TypeComp SharpnessVolume and Audio Lock Audio Menu FunctionsBalance and Fade BassTreble Loudness Maintenance Cleaning the LensReplacing the Projection Lamps Opening the Lamp Door Replacing Batteries in the Remote Control Bulb GuardInstalling New Batteries Replacing the FuseLocating the Fuse Removing the Fuse Holder Troubleshooting Before You Call for AssistanceProblem Color or VGA text not being projected Solutions to Common ProblemsProblem Nothing on screen Problem Image is not centered on the screen Problem Only the test pattern is displayedProblem Image is too wide or narrow for screen Problem Image is out of focusProblem Image and menus are reversed left to right Problem LitePro displays vertical lines, bleeding or spotsProblem Image is noisy or streaked Problem Projected colors don’t match the monitor’s colorsSpecifications AppendixAppendix Accessories Cable Connector Pin Assignments LCD ConnectorMonitor and VGA Connectors GNDLaptop Display Activation Chart ASTFN-F1 Appendix Index Assistance, see Technical Support audioLite show button 22 LitePro Quadra, see Macintosh Index Limited Warranty 010-0060-05 USA