BenQ W100 user manual Regulatory and legal information

Page 6

Moisture condensation

Never operate the projector immediately after moving it from a cold location to a hot location. When the projector is exposed to such a change in temperature, moisture may condense on the crucial internal parts. To prevent the projector from possible damage, do not use the projector for at least 2 hours after a sudden change in temperature.

Avoid using volatile liquids

Do not use volatile liquids, such as insecticide or some types of cleaner, near the projector. Do not leave rubber or plastic products touching the projector for a long time. They will leave marks on the finish. When cleaning, be sure to follow the cleaning product’s safety instructions.

Disposal

This product contains the following materials which are harmful to humans and the environment.

Lead, which is contained in solder.

Mercury, which is used in the lamp.

To properly dispose of the product or used lamps, consult your local environmental authority for advice.

Regulatory and legal information

FCC statement

CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the distance between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

EEC statement

This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electronic Magnetic Compatibility) and fulfills these requirements.

MIC statement

B class equipment (Household purpose info/telecommunications equipment)

This equipment has undergone EMC registration for household purpose, and can be used in any area including residential area.

WEEE directive

Disposal of Waste Electrical and Electronic Equipment by users in private households in the European Union.

This symbol on the product or on the packaging indicates that this can not be disposed of as household waste. You must dispose of your waste equipment by handling it over to the applicable take-back scheme for the recycling of electrical and electronic equipment. For more information about recycling of this equipment, please contact your city office, the shop where you purchased the equipment or your household waste disposal service. The recycling of materials will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and environment.

6

Safety, regulatory and legal information

Image 6
Contents Page Table of contents Safety, regulatory and legal information Safety instructionsDo not place inflammables near the projector Safety Instructions Regulatory and legal information Projector features IntroductionShipping contents Rear side Projector exterior viewFront / upper side Lower sideControls and functions ProjectorRemote control Remote control operationReturns all settings to the factory preset values Positioning your projector Choosing a locationSafety instructions for ceiling mounting of the projector Obtaining a preferred projected image sizeAspect image in a 169 aspect display area Positioning your projector Installation for a 169 ratio screen Installation for a 43 ratio screen Best video quality Connecting Video source devicesConnection Better video qualityConnecting Audio Computer Connecting a DVI source deviceWith a DVI DVI-I or DVI-D cable With a VGA to DVI-A cable ProjectorConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to an composite Video source deviceSwitching input signal OperationStart up Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone For exampleOperating in a high altitude environment Personalizing the projector menu displayOptimizing the image Selecting the aspect ratioPC/ DVI-A Signal Input Selecting an application modeOther adjustments DVI-D/ YPbPr/ S-Video/ Video Signal InputAdjusting tint Adjusting contrastAdjusting color Selecting a color temperatureShutting down the projector Using the menusDisconnect the power cord from the wall socket Menu operationMenu system Picture menu Pro-Picture menu Setting menu Advance menu Information menu Maintenance Care of the projectorLamp information Calculation of lamp hourReplacing the lamp Pull the lamp from the projector Restart the projectorTemperature information IndicatorsIllustration Projector needs 90 seconds to cool down. Or Please contact your dealer for assistanceTroubleshooting Plug the power cord into the AC inlet onAdjust the focus of the lens using the focus ring Specifications Projector specificationsDimensions Supported timing for PC input Timing chartHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Supported timing for Video and S-Video inputsWarranty Limited warrantyFor other information, please visit support.BenQ.com Copyright Disclaimer