BenQ W100 Adjusting the projected image, Adjusting the projection angle, Auto-adjusting the image

Page 24

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle.

To adjust the projector:

1.Press the front adjuster button and lift the front of the projector. Once the image is positioned where you want it,

release the front adjuster button to lock the foot in position.

Do not look into the lens while the lamp is on. The strong

light from the lamp may cause damage to your eyes.

Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from.

2.Screw the rear adjuster foot to fine tune the horizontal angle.

To retract the foot, hold up the projector while pressing the front adjuster button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

If the screen and the projector are not perpendicular to each other, the projected image becomes vertically trapezoidal. To correct this situation, adjust the value of Keystone in the Picture menu, on the projector control panel, or on the remote control.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the control panel of the projector or on the remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed at the bottom right of the screen for 3 seconds.

This function only works when a computer source is connected. The screen will be blank while Auto is functioning.

C T

Fine-tuning the image size and clarity

1. Adjust the projected image to the size that you 2.

Then sharpen the image by rotating the focus

need using the zoom ring.

ring.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24 Operation

Image 24
Contents Page Table of contents Safety, regulatory and legal information Safety instructionsDo not place inflammables near the projector Safety Instructions Regulatory and legal information Projector features IntroductionShipping contents Projector exterior view Front / upper sideRear side Lower sideControls and functions ProjectorRemote control Remote control operationReturns all settings to the factory preset values Positioning your projector Choosing a locationSafety instructions for ceiling mounting of the projector Obtaining a preferred projected image sizeAspect image in a 169 aspect display area Positioning your projector Installation for a 169 ratio screen Installation for a 43 ratio screen Connecting Video source devices ConnectionBest video quality Better video qualityConnecting Audio Connecting a DVI source device With a DVI DVI-I or DVI-D cable With a VGA to DVI-A cableComputer ProjectorConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to an composite Video source deviceSwitching input signal OperationStart up Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone For exampleOperating in a high altitude environment Personalizing the projector menu displayOptimizing the image Selecting the aspect ratioSelecting an application mode Other adjustmentsPC/ DVI-A Signal Input DVI-D/ YPbPr/ S-Video/ Video Signal InputAdjusting contrast Adjusting colorAdjusting tint Selecting a color temperatureUsing the menus Disconnect the power cord from the wall socketShutting down the projector Menu operationMenu system Picture menu Pro-Picture menu Setting menu Advance menu Information menu Maintenance Care of the projectorLamp information Calculation of lamp hourReplacing the lamp Pull the lamp from the projector Restart the projectorTemperature information IndicatorsIllustration Projector needs 90 seconds to cool down. Or Please contact your dealer for assistanceTroubleshooting Plug the power cord into the AC inlet onAdjust the focus of the lens using the focus ring Specifications Projector specificationsDimensions Timing chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSupported timing for PC input Supported timing for Video and S-Video inputsWarranty Limited warrantyFor other information, please visit support.BenQ.com Copyright Disclaimer