Motorola QIP7000 D15 Interactive Status, Interactive Status fields are, Unconfig, Macconnect

Page 76

Diagnostics

B

d15 Interactive Status

This diagnostic describes the interactive information that is displayed only when Thin Client platform is running. The information on the OSD and front panel is updated at least once every 5 seconds while the diagnostic is displayed. This is an example of a code module display with status descriptions:

Figure 30 – Interactive status front panel display

The Interactive Status fields are:

	Field	Description

	IP Address	The IP address in dotted-decimal format xxx.xxx.xxx.xxx assigned by the NC
		1500 to the QIP7000 series. 0.0.0.0 is displayed if the IP address is not
		configured or unknown.

	Downstream ID	A four-digit decimal value from 0000 to 9999 assigned by the DAC 6000 to the
		QIP7000 series. 0000 is displayed if the Downstream ID is not configured or if
		it is unknown.

	State	The interactive status of the QIP7000 series:

		Front		OSD	Description
		panel

		U		UNCONFIG	The QIP7000 series is not configured for
					the interactive system, and the platform
					should run as pre-interactive.

		C		MAC_CONNECT	The QIP7000 series is waiting to establish


QIP7000 (P2) Series Hybrid QAM/IP HD Set-top Terminal • Installation Manual						68
574702-001 a			This document is uncontrolled pending incorporation in a Motorola CMS

Image 76

Contents QIP7000 P2 Series Page Safety and Compliance During Installation FCC Declaration of Conformity Contents Operational Check for the Remote Control D01D02 D03Figures 1Introduction QIP7232 Front and rear views Features TunersStandard Data Features Calling for Repairs Getting HelpCompany From USA or Canada Outside USA or Canada Rear Panel Front PanelLabel Description Card Lable DescriptionSystem Overview PON OverviewFttp PON carries the following services Service DescriptionWhole Home IP Video CPE overview OOB MoCAWAN LAN Multi-Room DVR Multi room DVR networkInstallation Whole Home IP Video Network InstallationBefore You Begin During the installationConnect to the ONT After you finish connecting the components Checking the Home Coaxial Network TopologyVideo Connection Options Marginal MoCA network performanceIf you make any changes to the network, repeat steps 1 Connection TV Type DescriptionClearing the Hard Drive Audio Connection OptionsConnection Type Description Connecting to the ONT Connecting to the ONT with embedded MoCA MoCA technologyONT1000M Connections Key Name DescriptionConnecting the Home Router Connecting Homes with Multiple Existing Cable DropsConnecting the Home Router embedded MoCA ONT Installation Overview Determine if you are connecting to aCabling to an Hdtv for Video Cabling to an HdtvCabling to an Hdtv for Audio Cabling to an Hdtv for AudioCabling to an Hdtv and A/V Receiver for Video Cabling to an Hdtv and A/V Receiver Cabling to a Standard-Definition TV Cabling to a Standard Definition stereo TVCabling to a Standard-Definition TV, A/V Receiver and VCR Cabling to a Standard Definition TV, A/V Receiver and VCRQIP7000 series front panel provides Data Device ConnectionsPort type Description Operational Check for the Remote Control Optimizing the High-Definition SettingsFeature Testing Procedure Verifying the MoCA NetworkSetting Description Setting Description Graphics Overlaying the Video 4Diagnostics Using the DiagnosticsD01 General Status Example General Status display no error Field Description General Status fields areROM ID Front panel display for Purchase Status diagnostic D02 Purchase StatusPurchase Status fields are FieldFront panel display for the OOB diagnostic D03 Out-Of-Band OOB StatusOut-Of-Band Status fields are Agile OOB Tuner Hunting Front panel display for in-band diagnostic D04 In-Band StatusIn-Band Status fields are Carrier locked Carrier not locked PCR LockD05 Unit Address/Security Front panel display of a unit addressSeparable Security Unit Address fields areEMM EMM SCC SccecmSeparable Security fields are SignD06 Current Channel Status Current Channel status fields are DigitalCCI APSCIT DRMD07 Upstream Status Ethernet Return front panel displayEthernet Return fields are D08 Code Modules Front panel display for code modules Code Modules fields are D09 Memory Configuration NvramAudio Spdif D10 Audio/Video StatusIEC958PCM Unmuted BlackField Description D11 Interface/Port Status Page Interface Status fields are D12 User Setting Status Definition 480i format 720 x 480 pixels D13 DVR/Hard Drive Status DVR/Hard Drive Status fields are OSDD14 Application Specific Information Unconfig D15 Interactive StatusInteractive Status fields are MacconnectInitwaitdcorc WaitlmackWaitsoack WaitlaorsoD16 Connected Home This diagnostic displays the MoCA network statusConnected Home Status fields are TX Data Rate Connected Home Link Status fields areD17 Key Pad / LED Test 5Troubleshooting Problem Possible SolutionProblem Possible Solution Off standby IP Network Issues Insufficient RF Network ThroughputUsing a diplexer to bypass a line amplifier Bypassing an Amplifier