Viking Access Systems f1 gate manual Maintenance, General Safety Precautions

Page 10

IMPORTANT SAFETY INFORMATION

!WARNING! Not Following these instructions may cause severe injury or death.

MAINTENANCE

Remove the Power Harness from the Control Board. (refer to page 18)

•Clean and lubricate the turning pins and gate hinges using the recommended lubricant.

•Check that all hardware of the gate operator is properly tighten.

•Ensure that the gate moves freely.

•Check for corroded parts and replace if necessary.

•Check the battery for the following:

-Battery connections must be free of corrosion.

-Battery voltage must be 26VDC (fully charged battery).

Reconnect the Power Harness for the Control Board. (refer to page 18)

•Check and confirm the proper operation of all safety devices (photoelectric eye, edge sensors or like).

•Check and confirm the operation of all installed accessories.

•Check and confirm the operation of all special features such as the Intelligent

Obstruction Sensor, Hold Open Timer. (refer to page 24 and 26)

•Check and confirm the operation of the manual release. (refer to page 11)

•Verify the functionally of the battery backup, or power failure option, by turning off the main power source (115VAC or 230VAC). DO NOT FORGET TO

TURN ON THE MAIN POWER SOURCE AFTER VERIFICATION.

GENERAL SAFETY PRECAUTIONS

The following precautions are an integral and essential part of the product and must be supplied to the user. Read them carefully as they contain important indications for the safe installation, use and maintenance.

•These instruction must be kept and forwarded to all possible future users of the system.

•This product must be used only for that which it has been expressly designed.

•Any other use is to be considered improper and therefore dangerous.

•The manufacturer cannot be held responsible for possible damage caused by improper, erroneous or unreasonable use.

•Avoid operating in the proximity of the hinges or moving mechanical parts.

•Do not enter the path of the moving gate while in motion.

•Do not obstruct the motion of the gate as this may cause a situation of danger.

•Do not allow children to play or stay within the path of the moving gate.

•Keep remote control or any other control devices out of the reach of children, in order to avoid possible involuntary activation of the gate operator.

•In case of break down or malfunctioning of the product, disconnect from the main power source. Do not attempt to repair or intervene directly, contact only qualified personnel for repair.

•Failure to comply with the above may create a situation of danger.

•All cleaning, maintenance or repair work must be carried out by qualified personnel.

•In order to guarantee that the system works efficiently and correctly it is important to have the manufacturer’s instructions on maintenance of the gate and operator carried out by qualified personnel.

•In particular, regular checks are recommended in order to verify that the safety devices are operating correctly.

All installation, maintenance and repair work must be documented and made available to the user.

8

VIKING TECHNICAL SUPPORT 1.800.908.0884

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Instructions Viking F-1 Swing Gate Operator Vehicular Gate Operator Revision F1NXMN10.D October Parts Diagram DescriptionOperator References Limit Setup Buttons Control Board ReferencesTable of Contents Important Safety Instructions Important Safety InformationImportant Installation Instructions Important Installation Instructions Maintenance General Safety PrecautionsUL325 Gate Operator Classifications Install the gate operator only whenGlossary Photo Beam non-contact sensor Installation Secondary Entrapment ProtectionManual Release Edge Sensor contact sensor InstallationWhen manual operation is required To resume normal operationAudible Alarm Reset Switch Installation Manual Reset for the Audible AlarmAlternative Power 24VAC / VDC 60VA or Solar SpecificationsSingle Phase 50Hz / 60Hz Locate Control ButtonsGate Operator Installation Concrete Pad OptionPost Mounting Option Required ADD-ON PART# VA-F1PSOperator Positioning Technical Tips Operator and Arm GeometryStep Tips for proper ground installation Electrical InstallationHigh Voltage Supply Option Low Voltage Supply Option Solar Supply OptionAt the Limit Cam & Holder assembly Limits Setup1a 1b Limits Setup Two Wire Communication MASTER/SLAVE SetupCable Requirements Wireless Communication Options Required ADD-ON Choose option a or BODS Initial SettingsTimer Hold Open Timer Obstruction Detection SensorLast Open Power Failure Option Control Board SetupAuto Open Power Failure Option Fail Safe ModeODS Obstruction Detection Sensor When the Obstruction Sensor detects an obstruction it willObstruction Sensor Primary Entrapment Protection Flashing OverloadViking Heater Viking Lock ModeUse the LCD Display to activate this feature To set the heater to turn on at the Close LimitThis page Left Blank Intentionally COM + Accessory ConnectionsRe-Open Photo Beam vehicular Safety Check for proper operationOpen-Stop-Close Radio Receiver TypicalOpen Only Guard Station Anti-Tailgate, Open Commands & Guard StationOpen Commands ATG Anti-TailgateViking Loop Rack Accessory Connections Guidelines for Loop InstallationMagnetic Lock, Lock Solenoid Power for the LocksMagnetic Lock Lock Solenoid Synchronization with B-12 Barrier Arm B-12 Synchronization OptionTroubleshooting LED ReferencesTroubleshooting LCD MSG Meaning LCD Display ReferencesTroubleshooting Error Messages Solutions CheckAccess Control Connections Power ConnectionsGeneral Appendix aRelays In General Technical TIP Viking usesCommon Radio Receivers Connections Panels Appendix CSolar Applications Batteries & FuseViking Expansion Products Viking Konnect Diagnostic Tool On-site remoteViking Konnect Master/Slave Kit Secure and reliable OUR Continuous Commitment to Excellence Standard Features

f1 gate specifications

Viking Access Systems has long been recognized as an industry leader in providing reliable, high-quality access control solutions, and their F1 Gate is a prominent example of this commitment to innovation and security. Designed to enhance the functionality and aesthetics of any residential or commercial property, the F1 Gate combines advanced technology with robust materials to ensure both durability and performance.

One of the standout features of the F1 Gate is its modular design. This system allows for customization according to the specific needs and preferences of the user. Whether for a driveway, garden, or secured entryway, the F1 Gate can be tailored in terms of size, style, and materials, providing versatility for any application. The gate can be crafted from high-grade steel or aluminum, ensuring long-lasting strength and resistance to weather conditions.

Incorporating cutting-edge automation technology, the F1 Gate operates smoothly and efficiently. It features a powerful motor that guarantees quick opening and closing, coupled with a silent operation to minimize disruption. Users can enjoy seamless access through a variety of control options, including remote controls, keypads, and smartphone applications, providing flexibility in managing entry points.

Safety is a top priority in the F1 Gate design. It comes equipped with advanced safety features such as obstacle detection and automatic reversing systems. These technologies ensure that the gate will halt or reverse if an obstruction is detected, protecting vehicles, pets, and pedestrians alike. Additionally, the gate can integrate with existing security systems, adding another layer of protection to properties.

The F1 Gate also boasts significant energy efficiency. With intelligent power management systems, it is designed to consume minimal energy, making it an eco-friendly choice for those conscious about their environmental impact without sacrificing functionality.

Aesthetically, Viking Access Systems understands the importance of curb appeal. The F1 Gate offers various finishes and colors, allowing users to select an option that complements their property’s architecture. The sleek design enhances the overall look while providing a secure barrier against unauthorized access.

In summary, the Viking Access Systems F1 Gate combines versatility, safety, technology, and aesthetic appeal. Its robust construction and advanced features make it an excellent choice for those seeking a reliable and stylish access solution, perfect for any environment and requirement. As technology continues to evolve, the F1 Gate stands at the forefront, embodying the future of secure access control.
Top Page Image Contents