Viking Access Systems f1 gate manual Control Board References, Limit Setup Buttons

Page 6

CONTROL BOARD REFERENCES:

1.POWER HARNESS CONNECTOR provides power to the control board. pg 18-19

2.“OPEN LEFT” & “OPEN RIGHT” provides power to the motor. pg 20

3.LIMIT SETUP BUTTONS

available for future developments.

4.FEATURE ACTIVATION TRIM POTS activate and set features. pg 24

5.“EPS1” CONNECTOR

available for future developments.

6.“EPS2” CONNECTOR

available for future developments.

7.EMI BOARD CONNECTOR

monitors the high voltage power supply.

8.“CHECK MOTOR” Status LED indicates motor power status. pg 36

9.“BATTERY LOW” Status LED

indicates battery power status. pg 36

10.“POWER” Status LED

control board power status. pg 18,36

11.“MAGNETIC LOCK RELAY” Status LED status of this on-board relay. pg 34, 36

12.“MAGNETIC LOCK RELAY” Terminal Block connect electric locks here. pg 34, 36

13.INPUT STATUS LEDs

indicates input status. pg 36-37

14.ACCESS CONTROL TERMINAL BLOCKS accessory connections. pg 29-32, 42-44

15.“MASTER/SLAVE” Terminal Block wired master/slave connection. pg 22

16.CONTROL BOARD MOUNTING HOLES secures and grounds the control board.

17.“Siren” Terminal Block

Vikings UL Siren is connected here.

18.ON-BOARD 3 BUTTON STATION controls the gate during set up.

19.“AUX. PWR” Terminal Block

used for solar applications & in-motion warning devices. pg 19, 25

20.FEATURE ACTIVATION PIN HEADERS activate features by placing a jumper onto the pin headers. pg 25

21.“DIAGNOSE” Button

allows you to navigate through the Diagnostics LCD Display. pg 38-40

22.“DIAGNOSE” LED

informs that errors have been detected and available on LCD Display. pg 38-40

23.LCD DIAGNOSTICS DISPLAY

provides error messages, diagnostics and operator status information. pg 38-40

24.EXPANSION PRODUCT CONNECTIONS connections for additional products from Viking Access Systems. pg 46

25.“FAIL SAFE/SECURE” Jumper power failure option. pg 25

26.FUSE HOLDER - 15 AMP for motor circuit.

27.FUSE HOLDER - 4 AMP for charging circuit.

28.HEAT SINK

secures the control board and dissipates heat.

4	VIKING TECHNICAL SUPPORT 1.800.908.0884

Image 6

Contents Instructions Viking F-1 Swing Gate Operator Vehicular Gate Operator Revision F1NXMN10.D October Parts Diagram DescriptionOperator References Limit Setup Buttons Control Board ReferencesTable of Contents Important Safety Information Important Safety InstructionsImportant Installation Instructions Important Installation Instructions Maintenance General Safety PrecautionsInstall the gate operator only when UL325 Gate Operator ClassificationsGlossary Photo Beam non-contact sensor Installation Secondary Entrapment ProtectionManual Release Edge Sensor contact sensor InstallationWhen manual operation is required To resume normal operationAudible Alarm Reset Switch Installation Manual Reset for the Audible AlarmAlternative Power 24VAC / VDC 60VA or Solar SpecificationsSingle Phase 50Hz / 60Hz Locate Control ButtonsGate Operator Installation Concrete Pad OptionPost Mounting Option Required ADD-ON PART# VA-F1PSOperator Positioning Technical Tips Operator and Arm GeometryStep Electrical Installation Tips for proper ground installationHigh Voltage Supply Option Low Voltage Supply Option Solar Supply OptionLimits Setup At the Limit Cam & Holder assembly1a 1b Limits Setup MASTER/SLAVE Setup Two Wire CommunicationCable Requirements Wireless Communication Options Required ADD-ON Choose option a or BODS Initial SettingsTimer Hold Open Timer Obstruction Detection SensorLast Open Power Failure Option Control Board SetupAuto Open Power Failure Option Fail Safe ModeODS Obstruction Detection Sensor When the Obstruction Sensor detects an obstruction it willObstruction Sensor Primary Entrapment Protection Flashing OverloadViking Heater Viking Lock ModeUse the LCD Display to activate this feature To set the heater to turn on at the Close LimitThis page Left Blank Intentionally COM + Accessory ConnectionsRe-Open Photo Beam vehicular Safety Check for proper operationRadio Receiver Typical Open-Stop-CloseOpen Only Guard Station Anti-Tailgate, Open Commands & Guard StationOpen Commands ATG Anti-TailgateViking Loop Rack Accessory Connections Guidelines for Loop InstallationPower for the Locks Magnetic Lock, Lock SolenoidMagnetic Lock Lock Solenoid Synchronization with B-12 Barrier Arm B-12 Synchronization OptionTroubleshooting LED ReferencesTroubleshooting LCD MSG Meaning LCD Display ReferencesTroubleshooting Error Messages Solutions CheckAccess Control Connections Power ConnectionsGeneral Appendix aRelays In General Technical TIP Viking usesCommon Radio Receivers Connections Panels Appendix CSolar Applications Batteries & FuseViking Konnect Diagnostic Tool On-site remote Viking Expansion ProductsViking Konnect Master/Slave Kit Secure and reliable OUR Continuous Commitment to Excellence Standard Features