Viking Access Systems f1 gate Control Board Setup, Auto Open Power Failure Option, Fail Safe Mode

Page 27

CONTROL BOARD SETUP

Initial Settings

NOTE: Installing a shunt or jumper on the pins will activate the feature.

“Auto Open” - Power Failure Option

Opens the gate automatically during power failure. Resumes normal operation when power is restored.

“Fail Safe/Secure”

During complete power failure, including battery power; determines the force required to manually move the gate.

•Fail Safe Mode:

By removing the wire- jumper plug from the “Fail Safe/Secure” connector: The gate can move manually with a relatively low amount of force.

•Fail Secure Mode: By inserting the wire- jumper plug into the “Fail Safe/Secure” connector: The gate will not move manually.

“Last Open” - Power Failure Option

Opens the gate automatically when the battery backup voltage is critically low.

“Pre-Warning”Initiates two options for an audio or visual warning 3 seconds prior to gate motion and will continue:

1.Until gate reaches closed limit: “Magnetic Lock” terminals provide a contact between “COM” and “N.O”.

2.Until gate reaches either limit:

“AUX. PWR” terminals provide 24VDC.

“Sync” Used only in conjunction with the Viking Barrier gate operator model B-12. Activating this feature allows for synchronized operation with the B-12 operator. See page 35.

“EXT” Available for future developments.

!IMPORTANT: Regardless of the power failure options chosen, the gate can be moved manually with a relatively low amount of force by following the steps for “Manual Release” as outlined at on page 11.

VIKING TECHNICAL SUPPORT 1.800.908.0884	2 5

Image 27

Contents Instructions Viking F-1 Swing Gate Operator Vehicular Gate Operator Revision F1NXMN10.D October Description Parts DiagramOperator References Control Board References Limit Setup ButtonsTable of Contents Important Safety Information Important Safety InstructionsImportant Installation Instructions Important Installation Instructions General Safety Precautions MaintenanceInstall the gate operator only when UL325 Gate Operator ClassificationsGlossary Secondary Entrapment Protection Photo Beam non-contact sensor InstallationTo resume normal operation Edge Sensor contact sensor InstallationWhen manual operation is required Manual ReleaseManual Reset for the Audible Alarm Audible Alarm Reset Switch InstallationLocate Control Buttons SpecificationsSingle Phase 50Hz / 60Hz Alternative Power 24VAC / VDC 60VA or SolarConcrete Pad Option Gate Operator InstallationRequired ADD-ON PART# VA-F1PS Post Mounting OptionTechnical Tips Operator and Arm Geometry Operator PositioningStep Electrical Installation Tips for proper ground installationHigh Voltage Supply Option Solar Supply Option Low Voltage Supply OptionLimits Setup At the Limit Cam & Holder assembly1a 1b Limits Setup MASTER/SLAVE Setup Two Wire Communication Cable Requirements Required ADD-ON Choose option a or B Wireless Communication OptionsObstruction Detection Sensor Initial SettingsTimer Hold Open Timer ODSFail Safe Mode Control Board SetupAuto Open Power Failure Option Last Open Power Failure OptionFlashing Overload When the Obstruction Sensor detects an obstruction it willObstruction Sensor Primary Entrapment Protection ODS Obstruction Detection SensorTo set the heater to turn on at the Close Limit Viking Lock ModeUse the LCD Display to activate this feature Viking HeaterThis page Left Blank Intentionally Check for proper operation Accessory ConnectionsRe-Open Photo Beam vehicular Safety COM +Radio Receiver Typical Open-Stop-CloseOpen Only ATG Anti-Tailgate Anti-Tailgate, Open Commands & Guard StationOpen Commands Guard StationViking Loop Rack Guidelines for Loop Installation Accessory ConnectionsPower for the Locks Magnetic Lock, Lock SolenoidMagnetic Lock Lock Solenoid Barrier Arm B-12 Synchronization Option Synchronization with B-12LED References TroubleshootingTroubleshooting LCD Display References LCD MSG MeaningTroubleshooting Error Messages Check SolutionsPower Connections Access Control ConnectionsTechnical TIP Viking uses Appendix aRelays In General GeneralCommon Radio Receivers Connections Batteries & Fuse Appendix CSolar Applications PanelsViking Konnect Diagnostic Tool On-site remote Viking Expansion ProductsViking Konnect Master/Slave Kit Secure and reliable OUR Continuous Commitment to Excellence Standard Features