Viking Access Systems f1 gate manual Important Installation Instructions

Page 9

IMPORTANT SAFETY INFORMATION

!WARNING! Not Following these instructions may cause severe injury or death.

IMPORTANT INSTALLATION INSTRUCTIONS (Continued)

6.Controls intended for user activation must be located at least six feet (6’) away from any moving part of the gate and where the user is prevented from reaching over, under, around or through the gate to operate the controls.

Exception: Emergency access controls only accessible by authorized personnel (i.e. fire, police, EMS) may be placed at any location in the line-of-sight of the gate.

7.The Stop and/or Reset button must be located in the line-of-sight of the gate. Activation of the reset control shall not cause the operator to start.

8.A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily visible.

9.For gate operators using non-contact sensors (Photo Beams or like) in accordance with section 31.1.1 of the UL standard:

a.See instructions on the placement of non-contact sensors for each type of application (refer to page 10).

b.Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while the gate is still moving, and

c.One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the perimeter reachable by a moving gate or barrier (refer to page 10).

d.Use only Omron E3K-R10K4 photoelectric eye to comply with UL 325

10.For a gate operator utilizing a contact sensor (Edge sensor or like) in accordance with section 31.1.1 of the UL 325 standard:

a.One or more contact sensors shall be located where the risk of entrapment or obstruction exists, such as a the leading edge, trailing edge, and post mounted both inside and outside of a vehicular horizontal slide gate.

b.One or more contact sensors shall be located at the bottom of a vehicular vertical lift gate.

c.One or more contact sensors shall be located at the pinch point of a vehicular vertical pivot gate.

d.A hardwired contact sensor shall be located and its wiring arranged so that the communication between the sensor and the gate operator is not subject to mechanical damage.

e.A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate operator for entrapment protection functions shall be located where the transmission of the signals are not obstructed or impeded by building structures, natural landscaping or similar obstructions. A wireless contact sensor shall function under the intended end-use conditions.

f.One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally, if the bottom edge of a swing gate is greater than 6 inches (152 mm) above the ground at any point in its arc of travel, one or more contact sensors shall be located at the bottom edge (refer to page 11).

g.One or more contact sensors shall be located at the bottom edge of a vertical barrier (arm).

h.Only Use Miller Edge Model MGR20 or MGS20 edge sensor to comply with UL325.

VIKING TECHNICAL SUPPORT 1.800.908.0884

7

 

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Instructions Viking F-1 Swing Gate Operator Vehicular Gate Operator Revision F1NXMN10.D October Description Parts DiagramOperator References Control Board References Limit Setup ButtonsTable of Contents Important Safety Information Important Safety InstructionsImportant Installation Instructions Important Installation Instructions General Safety Precautions MaintenanceInstall the gate operator only when UL325 Gate Operator ClassificationsGlossary Secondary Entrapment Protection Photo Beam non-contact sensor InstallationWhen manual operation is required Edge Sensor contact sensor InstallationManual Release To resume normal operationManual Reset for the Audible Alarm Audible Alarm Reset Switch InstallationSingle Phase 50Hz / 60Hz SpecificationsAlternative Power 24VAC / VDC 60VA or Solar Locate Control ButtonsConcrete Pad Option Gate Operator InstallationRequired ADD-ON PART# VA-F1PS Post Mounting OptionTechnical Tips Operator and Arm Geometry Operator PositioningStep Electrical Installation Tips for proper ground installationHigh Voltage Supply Option Solar Supply Option Low Voltage Supply OptionLimits Setup At the Limit Cam & Holder assembly1a 1b Limits Setup MASTER/SLAVE Setup Two Wire CommunicationCable Requirements Required ADD-ON Choose option a or B Wireless Communication OptionsTimer Hold Open Timer Initial SettingsODS Obstruction Detection SensorAuto Open Power Failure Option Control Board SetupLast Open Power Failure Option Fail Safe ModeObstruction Sensor Primary Entrapment Protection When the Obstruction Sensor detects an obstruction it willODS Obstruction Detection Sensor Flashing OverloadUse the LCD Display to activate this feature Viking Lock ModeViking Heater To set the heater to turn on at the Close LimitThis page Left Blank Intentionally Re-Open Photo Beam vehicular Safety Accessory ConnectionsCOM + Check for proper operationRadio Receiver Typical Open-Stop-CloseOpen Only Open Commands Anti-Tailgate, Open Commands & Guard StationGuard Station ATG Anti-TailgateViking Loop Rack Guidelines for Loop Installation Accessory ConnectionsPower for the Locks Magnetic Lock, Lock SolenoidMagnetic Lock Lock Solenoid Barrier Arm B-12 Synchronization Option Synchronization with B-12LED References TroubleshootingTroubleshooting LCD Display References LCD MSG MeaningTroubleshooting Error Messages Check SolutionsPower Connections Access Control ConnectionsRelays In General Appendix aGeneral Technical TIP Viking usesCommon Radio Receivers Connections Solar Applications Appendix CPanels Batteries & FuseViking Konnect Diagnostic Tool On-site remote Viking Expansion ProductsViking Konnect Master/Slave Kit Secure and reliable OUR Continuous Commitment to Excellence Standard Features

f1 gate specifications

Viking Access Systems has long been recognized as an industry leader in providing reliable, high-quality access control solutions, and their F1 Gate is a prominent example of this commitment to innovation and security. Designed to enhance the functionality and aesthetics of any residential or commercial property, the F1 Gate combines advanced technology with robust materials to ensure both durability and performance.

One of the standout features of the F1 Gate is its modular design. This system allows for customization according to the specific needs and preferences of the user. Whether for a driveway, garden, or secured entryway, the F1 Gate can be tailored in terms of size, style, and materials, providing versatility for any application. The gate can be crafted from high-grade steel or aluminum, ensuring long-lasting strength and resistance to weather conditions.

Incorporating cutting-edge automation technology, the F1 Gate operates smoothly and efficiently. It features a powerful motor that guarantees quick opening and closing, coupled with a silent operation to minimize disruption. Users can enjoy seamless access through a variety of control options, including remote controls, keypads, and smartphone applications, providing flexibility in managing entry points.

Safety is a top priority in the F1 Gate design. It comes equipped with advanced safety features such as obstacle detection and automatic reversing systems. These technologies ensure that the gate will halt or reverse if an obstruction is detected, protecting vehicles, pets, and pedestrians alike. Additionally, the gate can integrate with existing security systems, adding another layer of protection to properties.

The F1 Gate also boasts significant energy efficiency. With intelligent power management systems, it is designed to consume minimal energy, making it an eco-friendly choice for those conscious about their environmental impact without sacrificing functionality.

Aesthetically, Viking Access Systems understands the importance of curb appeal. The F1 Gate offers various finishes and colors, allowing users to select an option that complements their property’s architecture. The sleek design enhances the overall look while providing a secure barrier against unauthorized access.

In summary, the Viking Access Systems F1 Gate combines versatility, safety, technology, and aesthetic appeal. Its robust construction and advanced features make it an excellent choice for those seeking a reliable and stylish access solution, perfect for any environment and requirement. As technology continues to evolve, the F1 Gate stands at the forefront, embodying the future of secure access control.
Top Page Image Contents