Viking Access Systems f1 gate manual Troubleshooting, LED References

Page 38

TROUBLESHOOTING

LED References

In addition to the LCD Display, the control board LEDs monitor the various circuits of the control board. Use the table below to identify the corresponding “TS Ref#” and refer to page 38-41 for further troubleshooting.

 

 

 

 

Page 41

#

LED

Status

Meaning

TS Ref#(s)

1

“Magnetic

OFF

At Closed Limit and Magnetic Lock Relay state is closed across “COM” &

 

 

Lock Relay”

 

“N.C”. (pg 34). Gate should be at the Close Limit.

 

 

 

SOLID

Not at Closed Limit and Magnetic Lock Relay state is closed across “COM” &

 

 

 

 

“N.O”. (pg 34). Gate should not be at the Close Limit

 

2

“Check Motor”

OFF

Normal Condition.

 

 

SOLID

The control board is sending power to the motor but the circuit is open.

3

“Battery Low”

OFF

Normal Condition.

 

 

SOLID

Batteries are low. Check power supply to the operator. (pg 18-19).

 

 

FLASHING

Batteries critically low. Check power supply to the operator. (pg 18-19).

4

“POWER”

SOLID

Normal Condition.

 

 

FLASHING

Operator is running on batteries only (pg 18-19).

 

 

OFF

No power to control board.

5

“Radio”

OFF

Normal Condition.

 

 

SOLID

Control Board is receiving an input from a device connected to the

 

 

 

Radio terminal (pg 30, 42).

6

“UL”

OFF

Normal Condition.

 

 

SOLID

Control Board is receiving an input from a device connected to the UL

 

 

 

terminal (pg 12-13, 42).

7

“Re-Open”

OFF

Normal Condition.

 

 

SOLID

Control Board is receiving an input from a device connected to the Re-

 

 

 

Open terminal (pg 29, 32, 42).

8

“ATG”

OFF

Normal Condition.

 

 

SOLID

Control Board is receiving an input from a device connected to the ATG

 

 

 

terminal (pg 31, 42).

7, 8

1, 2 1, 2

1, 2

1, 2, 4, 5

9, 10

9, 10

9, 10

9, 10

3 6

VIKING TECHNICAL SUPPORT 1.800.908.0884

 

 

Image 38
Contents Instructions Viking F-1 Swing Gate Operator Vehicular Gate Operator Revision F1NXMN10.D October Parts Diagram DescriptionOperator References Limit Setup Buttons Control Board ReferencesTable of Contents Important Installation Instructions Important Safety InformationImportant Safety Instructions Important Installation Instructions Maintenance General Safety PrecautionsGlossary Install the gate operator only whenUL325 Gate Operator Classifications Photo Beam non-contact sensor Installation Secondary Entrapment ProtectionManual Release Edge Sensor contact sensor InstallationWhen manual operation is required To resume normal operationAudible Alarm Reset Switch Installation Manual Reset for the Audible AlarmAlternative Power 24VAC / VDC 60VA or Solar SpecificationsSingle Phase 50Hz / 60Hz Locate Control ButtonsGate Operator Installation Concrete Pad OptionPost Mounting Option Required ADD-ON PART# VA-F1PSOperator Positioning Technical Tips Operator and Arm GeometryStep High Voltage Supply Option Electrical InstallationTips for proper ground installation Low Voltage Supply Option Solar Supply Option1a 1b Limits SetupAt the Limit Cam & Holder assembly Limits Setup Cable Requirements MASTER/SLAVE SetupTwo Wire Communication Wireless Communication Options Required ADD-ON Choose option a or BODS Initial SettingsTimer Hold Open Timer Obstruction Detection SensorLast Open Power Failure Option Control Board SetupAuto Open Power Failure Option Fail Safe ModeODS Obstruction Detection Sensor When the Obstruction Sensor detects an obstruction it willObstruction Sensor Primary Entrapment Protection Flashing OverloadViking Heater Viking Lock ModeUse the LCD Display to activate this feature To set the heater to turn on at the Close LimitThis page Left Blank Intentionally COM + Accessory ConnectionsRe-Open Photo Beam vehicular Safety Check for proper operationOpen Only Radio Receiver TypicalOpen-Stop-Close Guard Station Anti-Tailgate, Open Commands & Guard StationOpen Commands ATG Anti-TailgateViking Loop Rack Accessory Connections Guidelines for Loop InstallationMagnetic Lock Lock Solenoid Power for the LocksMagnetic Lock, Lock Solenoid Synchronization with B-12 Barrier Arm B-12 Synchronization OptionTroubleshooting LED ReferencesTroubleshooting LCD MSG Meaning LCD Display ReferencesTroubleshooting Error Messages Solutions CheckAccess Control Connections Power ConnectionsGeneral Appendix aRelays In General Technical TIP Viking usesCommon Radio Receivers Connections Panels Appendix CSolar Applications Batteries & FuseViking Konnect Master/Slave Kit Secure and reliable Viking Konnect Diagnostic Tool On-site remoteViking Expansion Products OUR Continuous Commitment to Excellence Standard Features

f1 gate specifications

Viking Access Systems has long been recognized as an industry leader in providing reliable, high-quality access control solutions, and their F1 Gate is a prominent example of this commitment to innovation and security. Designed to enhance the functionality and aesthetics of any residential or commercial property, the F1 Gate combines advanced technology with robust materials to ensure both durability and performance.

One of the standout features of the F1 Gate is its modular design. This system allows for customization according to the specific needs and preferences of the user. Whether for a driveway, garden, or secured entryway, the F1 Gate can be tailored in terms of size, style, and materials, providing versatility for any application. The gate can be crafted from high-grade steel or aluminum, ensuring long-lasting strength and resistance to weather conditions.

Incorporating cutting-edge automation technology, the F1 Gate operates smoothly and efficiently. It features a powerful motor that guarantees quick opening and closing, coupled with a silent operation to minimize disruption. Users can enjoy seamless access through a variety of control options, including remote controls, keypads, and smartphone applications, providing flexibility in managing entry points.

Safety is a top priority in the F1 Gate design. It comes equipped with advanced safety features such as obstacle detection and automatic reversing systems. These technologies ensure that the gate will halt or reverse if an obstruction is detected, protecting vehicles, pets, and pedestrians alike. Additionally, the gate can integrate with existing security systems, adding another layer of protection to properties.

The F1 Gate also boasts significant energy efficiency. With intelligent power management systems, it is designed to consume minimal energy, making it an eco-friendly choice for those conscious about their environmental impact without sacrificing functionality.

Aesthetically, Viking Access Systems understands the importance of curb appeal. The F1 Gate offers various finishes and colors, allowing users to select an option that complements their property’s architecture. The sleek design enhances the overall look while providing a secure barrier against unauthorized access.

In summary, the Viking Access Systems F1 Gate combines versatility, safety, technology, and aesthetic appeal. Its robust construction and advanced features make it an excellent choice for those seeking a reliable and stylish access solution, perfect for any environment and requirement. As technology continues to evolve, the F1 Gate stands at the forefront, embodying the future of secure access control.