Toshiba IK-TF5 instruction manual Table of Contents

TABLE OF CONTENTS

1. CAUTIONS ON USE AND INSTALLATION					5	7. 3 External Sync	22
2. COMPONENTS					5	( 1 ) External sync signal input conditions	22
3. ITEMS CONTROLLED BY USING						( 2 ) External sync frequency range	22
						( 3 ) Using the unit with external sync signal ..	23
ON SCREEN DISPLAY					6
						(3. 1) H (horizontal) phase adjustment	23
4. NAMES AND FUNCTIONS					7	( 4 ) Changing HD/VD input/output	23
5. CONNECTION					8	7. 4 Synchro. Scan Operatin	23
5. 1	Standard Connection				8	( 1 ) Setting by 1H	23
						( 2 ) Setting by the frame	23
5. 2	Cautions on Connection				8
						7. 5 EXT TRIG (External trigger)	24
5. 3	Connector Pin Assignments				8
6. OPERATION				.....................................................	9	( 1 ) 1P SNR (1 Pulse Sync Non Reset)	24
6. 1	White Balance				9	(1. 1) 1 Pulse Trigger SYNC-NON RESET
						Picture Output Timing	24
6. 2	Gain				10
			........................................................			(1. 2) 1 Pulse Trigger SYNC-NON RESET
6. 3	Shading Correction				10	Picture Output Timing (at Time of
7. MODE SETTING BY ON SCREEN DISPLAY					11	Internal Sync)	25
7. 1	Using the Menues				11	( 2 ) 1P SR (1 Pulse Sync Reset)	26
						(2. 1) 1 Pulse Trigger SYNC-RESET Picture
7. 2	Menus				12
				Output Timing		26
( 1 ) SHUTTER (Electronic shutter)					12	( 3 ) PW SNR (Pulse width trigger
	(1.	1) Changing each setting in				SYNC-NON RESET)	27
			MANU mode		12	(3. 1) Pulse Width Trigger SYNC-NON RESET
	(1.	2)	Changing each setting in			Picture Output Timing	27
			SS (synchro. scan) mode		13	(3. 2) Pulse Width Trigger SYNC-NON RESET
	(1.	3)	Changing each setting in			Picture Output Timing (at Time of
			E.TRG mode		14	Internal Sync)	28
	(1.	3. 1)		Changing each setting in		( 4 ) PW SR (Pulse width trigger
				1P SNR mode	14
						SYNC-RESET)	29
	(1.	3. 2)		Changing each setting in
						(4. 1) 1 Pulse Width Trigger SYNC-RESET
				1P SR mode	15
						Picture Output Timing	29
	(1.	3. 3)		Changing each setting in
						( 5 ) RR (Reset restart)	30
				PW SNR mode	16
						(5. 1) Long Term Exposure	30
	(1.	3. 4)		Changing each setting in
						(5. 2) Input Timing Chart Example	30
				PW SR mode	17
						7. 6 Partial Read	31
	(1.	3. 5)		Changing each setting in
				RR mode	18	( 1 ) Partial Scanning OFF
( 2 ) GAIN (Video gain)					18
						(All pixels scanning)	31
	(2.	1)	Changing each setting in GAIN		18	( 2 ) Partial Scanning ON	31
( 3 ) WHT BAL (White balance)					19
						( 3 ) When Partial Scanning Mode is ON	31
	(3.	1)	Changing each setting in AWB
						8. INPUT OUTPUT SIGNAL SPECIFICATOINS	32
			(Automatic White Balance) mode ....		19
	(3.	2)	Changing each setting in MANU		19	( 1 ) HD/VD Output Amplitude Specifications ...	32
			(Manual) mode			( 2 ) VIDEO INDEX Output Specifications	32
( 4 ) PROCESS					20
						( 3 ) VD Input Specifications	32
	(4.	1)	Changing master pedestal		20
						( 4 ) HD Input Specifications	32
	(4.	2)	Changing R pedestal		20
						( 5 ) Trigger Pulse Specifications	32
	(4.	3)	Changing B pedestal		20
	(4.	4)	Changing White clip		20	( 6 ) External HD/VD Input Phase
	(4.	5)	Changing shading correction mode ...		20	Specifications	32
	(4.	6)	Changing manual shading correction ..		20	9. CCD OUTPUT WAVEFORM TIMING CHART ...	33

( 5 ) SYNC		21
(5. 1)	Adjusting horizontal phase	21
(5. 2)	Changing RGB SYNC	21
( 6 ) OPTION		21
(6. 1)	Changing RS232C communication
	baud rate	21
( 7 ) Setting to factory setting status		22

( 1 ) Horizontal Output Waveform Timing Chart ... 33 ( 2 ) Vertical Output Waveform Timing Chart ... 33

10.	SPECIFICATIONS	34
11. EXTERNAL APPEARANCE DIAGRAM		35
12.	BEFORE MAKING A SERVICE CALL	35

4