Toshiba IK-TF5 instruction manual Specifications, RGB, 3CCD

Page 34

10. SPECIFICATIONS

Power supply	DC12V± 10%
Power consumption	Approx. 4.3W
Pick-up system	RGB, 3CCD
Image sensor	1/3inch All pixels CCD
(Effective pixels)	(Horizontal : 659pixels, Vertical : 494pixels)
Scanning system	Progressive scan
Scan frequency	Horizontal : 31.469kHz, Vertical : 59.94Hz
Sync system	Internal/External (Automatic switching)
Horizontal resolution	500TV lines
Sensitivity	F6.8 standard (2000 lx, 3000K)
Minimum illumination	14 lx (F2.2, Sensitivity + 18 dB, 3000K)
SN ratio	62 dB standard (G)
Lens mount	C mount (flange back : 17.526 mm in-air)
Ambient temperature	32 to 104° F (0 to 40° C)
Ambient humidity	Less than 90%
Weight	Approx. 5.74oz (165g)
External dimension	1.73” (W) x 1.73” (H) x 3.07” (D)
	(44 (W) x 44 (H) x 78 (D) mm)			(except for protruded portion)
White balance	AWB (Automatic white balance), MANUAL (Manual)
Gain	MANUAL (Manual), OFF (0 dB)
Output signal	RGB : 75Ω unbalanced, D sub 15 pin connector
External sync input	HD or VD :	2 – 5 V(p-p) Negative
Sync signal output	SYNC :	2.0V±	1 V(p-p) 75Ω unbalanced
	HD, VD, INDEX :	5V +0.5-1.0	V(p-p), Negative
		Load impedance : More than 10 kW
External trigger input	TRIGGER :	Low level : Less than 0.4V, High level : 3.4 – 5V
		1 Pulse : Positive/Negative/Width selectable
		2 Pulse : Positive/Negative/Width selectable
Interface	Serial data interface (RS-232C)
Optional parts	EXC-TF05B (RGB cable), etc

34

Image 34

Contents IK-TF5 For Customer UseSafety Precautions Disclaimer May occur in such placesTable of Contents Components Items Controlled by Using on Screen Display Available selectins Preset valueMenu Down button Connection Connector Pin AssignmentsStandard Connection Automatic White Balance Manual White Balance Outline OperationWhite Balance Result displayed MeaningGain Shutter speed mode is EXT Trig modeShading Correction Mode Setting by on Screen Display Using the MenusMenus Changing each setting in Manu modePartial read setting Shutter Electronic shutterChanging each setting in SS synchro. scan mode Changing the shutter speed settingChanging the polarity of inputting trigger pulse setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing 1P SNR exposure time settingChanging each setting in 1P SR mode Changing 1P SR exposure time settingChanging each setting in PW SNR mode Changing each setting in PW SR mode Changing the gain in Manu mode Changing each setting in RR modeChanging each setting in Gain Gain Video gainWHT BAL White balance Changing R pedestal Changing shading correction modeChanging master pedestal Changing B pedestalOption Adjusting horizontal phaseSync Changing RGB SyncShutter mode HD input VD input Setting to factory setting statusExternal sync signal input conditions External SyncSetting by 1H Setting by the frameUsing the unit with external sync signal Synchro. Scan Operation1P SNR 1 Pulse Sync Non Reset EXT Trig External triggerVD OUT*3 Video Index 1P SR 1 Pulse Sync Reset 1 Pulse Trigger SYNC-RESET Picture Output TimingPW SNR Pulse width trigger SYNC-NON Reset Video output 525H PW SR Pulse width trigger SYNC-RESET 1 Pulse Width Trigger SYNC-RESET Picture Output TimingInput Timing Chart Example RR Reset restartLong Term Exposure Partial Scanning OFF All pixels scanning When Partial Scanning Mode is onPartial Read Partial Scanning onInput Output Signal Specificatoins Horizontal Output Waveform Timing Chart CCD Output Waveform Timing ChartVertical Output Waveform Timing Chart Specifications RGB, 3CCDBefore Making a Service Call External Appearance DiagramSymptom Items to be checked Step-by-step Procedures How to Obtain Warranty Service Limited One 1 Year Warranty of Labor and PartsImaging Systems Division