Toshiba IK-TF5 Synchro. Scan Operation, Setting by the frame, Changing HD/VD input/output

Page 23

( 3 ) Using the unit with external sync signal

When adjusting H (horizontal) phase refer to the item "7.2 (5) (5.1) Adjusting horizontal phase".

(3. 1) H (horizontal) phase adjustment

Observe the external sync signal and the video signal output waveform of the unit with a dual trace oscilloscope, and ad- just H phase so that the H phases match.

External

Sync. signal Match

the phase.

Camera

Video output

( 4 ) Changing HD/VD input/output

(1)Put off 6 screws both on flank/top of camera chassis.

(2)Change internal switch SJ01(HD/VD).

HD/VD OUTPUT

SJ01

HD/VD INPUT high-impedance HD/VD INPUT 75(factory setting)

7. 4 Synchro. Scan Operation

The shutter speed can be set by the horizontal scanning period (1H) or by the frame.

( 1 ) Setting by 1H

1/525H to 524/525H stands for the setting by the 1H and the shutter speed can be set by the 1H (31.8 ms).

( 2 ) Setting by the frame

1FRM to 512FRM stand for the setting (long period exposure) by the frame.

The video signal stored during the frame period set is output as 1 frame video image at a frame interval specified.

VD output

Video output

Index output

(INDEX)

n

(4FRM setting)

n+1

23

Image 23
Contents For Customer Use IK-TF5Safety Precautions May occur in such places DisclaimerTable of Contents Components Available selectins Preset value Items Controlled by Using on Screen DisplayMenu Down button Standard Connection Connector Pin AssignmentsConnection Result displayed Meaning OperationWhite Balance Automatic White Balance Manual White Balance OutlineShading Correction Shutter speed mode is EXT Trig modeGain Using the Menus Mode Setting by on Screen DisplayShutter Electronic shutter Changing each setting in Manu modePartial read setting MenusChanging the shutter speed setting Changing each setting in SS synchro. scan modeChanging 1P SNR exposure time setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing the polarity of inputting trigger pulse settingChanging 1P SR exposure time setting Changing each setting in 1P SR modeChanging each setting in PW SNR mode Changing each setting in PW SR mode Gain Video gain Changing each setting in RR modeChanging each setting in Gain Changing the gain in Manu modeWHT BAL White balance Changing B pedestal Changing shading correction modeChanging master pedestal Changing R pedestalChanging RGB Sync Adjusting horizontal phaseSync OptionExternal Sync Setting to factory setting statusExternal sync signal input conditions Shutter mode HD input VD inputSynchro. Scan Operation Setting by the frameUsing the unit with external sync signal Setting by 1HEXT Trig External trigger 1P SNR 1 Pulse Sync Non ResetVD OUT*3 Video Index 1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Sync ResetPW SNR Pulse width trigger SYNC-NON Reset Video output 525H 1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETLong Term Exposure RR Reset restartInput Timing Chart Example Partial Scanning on When Partial Scanning Mode is onPartial Read Partial Scanning OFF All pixels scanningInput Output Signal Specificatoins Vertical Output Waveform Timing Chart CCD Output Waveform Timing ChartHorizontal Output Waveform Timing Chart RGB, 3CCD SpecificationsSymptom Items to be checked External Appearance DiagramBefore Making a Service Call Imaging Systems Division Limited One 1 Year Warranty of Labor and PartsStep-by-step Procedures How to Obtain Warranty Service