Toshiba IK-TF5 instruction manual Standard Connection, Connector Pin Assignments

Page 8

5.CONNECTION

5.1 Standard Connection

Lens

IK-TF5

Less than 4 mm

Camera cable
(option)	RGB
DC IN 12V	Image processing
	Image processing
DC power supply	equipments, etc.
DC power supply

5. 2 Cautions on Connection

•When connecting the camera cables, be sure to turn off the camera and the other equipment connected.

•We suggest using a C mount lens made for a 3CCD camera.

When using another lens, the best camera performance of this camera may not be obtained.

(For example, low resolution may occur, focus may be lost through the range of a zoom lens, and flare, ghost or shading may occur)

Furthermore, in order to avoid damaging the mounting portion of the camera head, use a lens which has projection dimension from the mounting base of less than 0.157"(4mm).

•For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA approved ungrounding type AC adaptor with the specifications described below.

Power supply voltage	: DC12V± 10%
Current rating	: More than 830 mA, Less than2.5A
Ripple voltage	: Less than 50 mV(p–p)
Connector	: HR10A–7P–4S by HIROSE electronics Co. Ltd
	Pins 1, 2	: 12V
	Pins 3, 4	: GND

5. 3 Connector Pin Assignments

DC IN 12V

1+12V

2+12V

3GND

4GND

8

			RGB
			1	R
			2	G
	1	3	3	B
	1	3	4	TXD	5	4	3	2	1
			4	TXD	5	4	3	2	1
	2	4	5	GND	10	9		8	7 6
			5	GND	10	9		8	7 6
			6	GND	15	14	13	12	11
			7	GND	15	14	13	12	11
			7	GND
			8	SYNC
			9	12V
			10	GND
			11	RXD
			12	TRIG
			13	HD IN/OUT
			14	VD IN/OUT
			15	INDEX

Image 8

Contents IK-TF5 For Customer UseSafety Precautions Disclaimer May occur in such placesTable of Contents Components Items Controlled by Using on Screen Display Available selectins Preset valueMenu Down button Standard Connection Connector Pin AssignmentsConnection Operation White BalanceAutomatic White Balance Manual White Balance Outline Result displayed MeaningShading Correction Shutter speed mode is EXT Trig modeGain Mode Setting by on Screen Display Using the MenusChanging each setting in Manu mode Partial read settingMenus Shutter Electronic shutterChanging each setting in SS synchro. scan mode Changing the shutter speed settingChanging each setting in E.TRG mode Changing each setting in 1P SNR modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingChanging each setting in 1P SR mode Changing 1P SR exposure time settingChanging each setting in PW SNR mode Changing each setting in PW SR mode Changing each setting in RR mode Changing each setting in GainChanging the gain in Manu mode Gain Video gainWHT BAL White balance Changing shading correction mode Changing master pedestalChanging R pedestal Changing B pedestalAdjusting horizontal phase SyncOption Changing RGB SyncSetting to factory setting status External sync signal input conditionsShutter mode HD input VD input External SyncSetting by the frame Using the unit with external sync signalSetting by 1H Synchro. Scan Operation1P SNR 1 Pulse Sync Non Reset EXT Trig External triggerVD OUT*3 Video Index 1P SR 1 Pulse Sync Reset 1 Pulse Trigger SYNC-RESET Picture Output TimingPW SNR Pulse width trigger SYNC-NON Reset Video output 525H PW SR Pulse width trigger SYNC-RESET 1 Pulse Width Trigger SYNC-RESET Picture Output TimingLong Term Exposure RR Reset restartInput Timing Chart Example When Partial Scanning Mode is on Partial ReadPartial Scanning OFF All pixels scanning Partial Scanning onInput Output Signal Specificatoins Vertical Output Waveform Timing Chart CCD Output Waveform Timing ChartHorizontal Output Waveform Timing Chart Specifications RGB, 3CCDSymptom Items to be checked External Appearance DiagramBefore Making a Service Call Imaging Systems Division Limited One 1 Year Warranty of Labor and PartsStep-by-step Procedures How to Obtain Warranty Service