Arcam Comprehensive Installation Guide for A80 and P80 Stereo Amplifiers

Page 4

Installation: A80 amplifier

POWER INLET

1

A80/P80

4

 

 

 

 

SP2

 

 

TRIG

 

4 – 16 OHMS

 

VOLTAGE

OUT

 

 

 

L

 

 

 

 

SELECT

 

 

 

SP1

 

REMOTE

 

 

 

 

 

 

 

R

 

IN

+

R

+ L

115/230V

 

 

2 3 4

Positioning the unit

Place your amplifier on a level, firm surface. Avoid placing the unit in direct sunlight or near sources of heat or damp.

Ensure adequate ventilation. Do not place the unit in an enclosed space such as a bookcase or cabinet as both of these will impede air flow through the ventilation slots.

Connecting to loudspeakers

You can connect one or two pairs of loudspeakers to your amplifier, provided each pair is rated between 8–16Ω. If one or both pairs have an impedance of less than 8Ω, the combined load on the amplifier falls below 4Ω and could cause an overload. If so, the overload protection circuit may engage and the amplifier will not work.

To connect one pair of loudspeakers, use the SP1 terminals.

SP1 and SP2 terminals 4

Both sets of loudspeaker terminals can be muted by pressing the MUTE button on the remote control. To switch SP1 and SP2 independently, use the front panel switches (see page 6, 2) or the remote control (see page 9).

Your amplifier is fitted with industry standard loudspeaker terminals. The terminal accepts spade terminals or bare wires.

To connect a spade terminal or bare wire, unscrew the red (or black) part of the loudspeaker terminal first. Insert the wire or spade terminal and screw it back up.

Caution: Do not over tighten the loudspeaker terminals or use a wrench, pliers, etc., as this could cause damage to the terminals which will not be covered under warranty.

Connect the right speaker to the terminals on the back of your amplifier marked R and the left speaker to the terminals marked L.

Connect your loudspeakers so that the red (positive/+) terminal on each loudspeaker is connected to the red (positive/+) terminal on the amplifier. Your loudspeaker cables may be marked to show polarity (negative/and positive/+), if not, then the positive terminal can usually be identified by a ridge or coloured marking.

Now connect your loudspeakers’ black (negative/) terminals to the black (negative/) terminals on the amplifier.

Ensure that no stray strands of inner wires are allowed to touch another cable or the amplifier’s casing. This can cause a short circuit and damage your amplifier!

 

TAPE

 

 

 

 

 

 

 

PRE OUT LINE OUT

RECORD

PLAY

DVD

AV

TUNER

CD

AUX

PHONO

 

OUT

IN

 

 

 

 

 

(MM)

5 6 7 8 9 bk bl bm bn bo

+

Arcam A80 amplifier

+

 

R

 

L

+

+

Right

 

 

Left

speaker

 

 

speaker

Wiring your loudspeakers

Connecting to a power supply

Mains lead

The appliance is normally supplied with a moulded mains plug already fitted to the lead. If for any reason the plug needs to be removed, it must be disposed of immediately and securely, as it is a potential shock hazard when inserted into the mains socket. Should you require a new mains lead, contact your Arcam dealer.

Wrong plug?

Check that the plug supplied with the unit fits your supply and that your mains supply voltage agrees with the voltage setting (115V or 230V) indicated on the rear panel of the unit 2 before plugging in.

If your mains supply voltage or mains plug is different, consult your Arcam dealer or Arcam Customer Support on +44 (0)1223 203200.

The product must be earthed.

Plugging in

Push the plug (IEC line socket) of the power cable supplied with the unit into the socket (POWER INLET) 1 in the back of the unit. Make sure it is pushed in firmly.

Put the plug on the other end of the cable into your power supply socket and switch the socket on.

Standby power

For remote standby operation, the amplifier’s control power supply is kept powered up all the time the unit is connected to the mains supply. The front panel power switch powers down all other circuitry. Power consumption in this mode is less than 2.5W.

Image 4
Contents A80 P80 Important safety instructions Safety guidelinesSafety compliance Safety Using this handbookContents Installation A80 amplifier Connecting to loudspeakersConnecting to a power supply Positioning the unitPre/power amplifier connections Different output typesUsing your A80 amplifier Front panel controlsRecording Tape-to-tape copying dubbingSetting up your A80 amplifier Adjusting listening settingsTo their factory defaults Menu mapUsing the remote control CR-389 Remote ControlConnecting to power, loudspeakers and other equipment Installation P80 power ampliferRemote switching Using your P80 power amplifier Power and power indicator lightBi-wiring your loudspeakers Bi-wiring and bi-amping loudspeakersBefore you start Service information Technical specificationsRemote-control codes Guarantee On-line registrationNormes de sécurité Consignes de sécuritéRespect des consignes de sécurité Utilisation de ce manuel SécuritéTable des matières DépannageMise en place de l’appareil Installation A80 integrated amplifierBranchement des haut-parleurs Branchement sur d’autres appareils BranchementAlimentation de veille Connexions préamplificateur/amplificateur de PuissanceCommandes du panneau avant Utilisation de l’amplificateur intégré A80Enregistrement Utilisation du bouton TapeIntroduction Réglage de l’amplificateur intégré A80Réglage des paramètres d’écoute Utilisation de la télécommande Télécommande CR-389Arrêt et mise en marche à l’aide de la télécommande Installation amplificateur de puissance P80Détection du signal Power et voyant lumineux d’alimentation Utilisation de l’amplificateur de puissance P80Avant de commencer Bi-câblage des haut-parleursDépannage Spécifications techniquesTableau des commandes IR Garantie Inscription en ligneSicherheitsrichtlinien SicherheitsrichtlinienEinhaltung von Sicherheitsbestimmungen Sicherheit Hinweise zum HandbuchInhalt Installation Vollverstärker A80 Aufstellen des GerätesAnschließen der Lautsprecher Anschließen der StromversorgungAnschließen anderer Geräte AnschließenStandby-Betrieb Vorverstärker/EndstufenanschlüsseBedienung des Vollverstärkers A80 Steuerelemente an der VorderseiteAufnahme Empfänger für die FernbedienungMaximum ‘On’ Volume Mit dem Hauptregler können Sie beim Einstellen des Vollverstärkers A80Einführung Anpassung der HöreinstellungenUP und Down Modell CR-389Tasten zum Auswählen der Audioquelle Installation Endstufe P80 SignalerkennungFernschaltung Indem Sie eine Verbindung vom Remote IN-Anschluss derBedienung der Endstufe P80 Bi-Wiring der Lautsprecher Bi-Wiring und Bi-Amping der LautsprecherErste Schritte Kundendienst Technische DatenTabelle der IR-Befehle Online-Registrierung Veiligheidsvoorschriften VeiligheidsrichtlijnenVeiligheidsnaleving Veiligheid InhoudsopgaveOp lichtnet, luidsprekers en andere apparatuur KlantendienstInstallatie geïntegreerde versterker A80 De eenheid plaatsenAansluiten op luidsprekers Aansluiting op het lichtnetAansluiting op andere apparatuur AansluitenStandby-modus Voorversterker-/eindversterkeraansluitingenUw geïntegreerde versterker A80 gebruiken Knoppen aan de voorkantOpnemen Kopiëren van tape naar tape dubbingUw geïntegreerde versterker A80 instellen Luisterinstellingen regelenVolume en dempen De afstandsbediening gebruikenAfstandsbediening CR-389 Omhoog en OmlaagInstallatie eindversterker P80 Op lichtnet, luidsprekers en andere apparatuur aansluitenOp afstand bedienen DoorlussenPower en aan-/uitlampje Bediening van uw eindversterker P80Bi-wiring en bi-amping van luidsprekers Bi-wiring van uw luidsprekersZo voert u bi-wiring van luidsprekers uit Voordat u begintKlantendienst Technische specificatiesCodes op de afstandsbediening StroomtoevoerinstructiesBronkeuze-instructies Menunavigatie-instructiesOnline-registratie A80/P80 A80/P80 Telephone +44 01223 Fax +44 01223 Issue

P80, A80 specifications

The Arcam P80 and A80 are two prominent products in the realm of high-fidelity audio, designed to offer audiophiles superior sound quality and a seamless listening experience. Arcam, renowned for its dedication to innovation and excellence, has equipped these models with advanced technologies that elevate their performance.

The Arcam P80 is a robust power amplifier that delivers a remarkable 80 watts per channel into 8 ohms. This powerful amplification ensures that even the most demanding speakers will be driven effortlessly, providing dynamic sound reproduction. One of the standout features of the P80 is its Class G amplification design. This technology enhances efficiency by utilizing multiple output stages, allowing the amplifier to switch between power levels depending on the signal demands. This minimizes distortion and maximizes sound quality, resulting in crystal-clear audio across various frequencies.

Equipped with high-quality components, the P80 employs a toroidal transformer that minimizes electromagnetic interference and optimizes power delivery. This attention to detail translates to a more refined sound, making it an excellent choice for both music enthusiasts and home theater setups. The amplifier also features multiple input options, including both balanced and unbalanced connections, ensuring compatibility with a wide range of audio sources.

On the other hand, the Arcam A80 is an integrated amplifier that combines both preamplifier and power amplifier functionalities into a single unit. With an output of 80 watts per channel into 8 ohms, it shares the P80's commitment to power and performance. The A80 incorporates a high-quality digital-to-analog converter, enhancing the sound quality of digital sources, and features multiple inputs for flexibility when connecting various devices.

The A80 also utilizes a high-grade phono stage for vinyl enthusiasts, enabling users to connect turntables directly and enjoy their favorite records with outstanding fidelity. The design emphasizes simplicity and elegance, with a user-friendly interface and intuitive controls, making it a perfect addition to both contemporary and traditional home audio setups.

In summary, the Arcam P80 and A80 represent the pinnacle of audio engineering, incorporating advanced technologies such as Class G amplification, high-quality DACs, and versatile input options. They deliver an exceptional listening experience, providing power, clarity, and musicality that will satisfy even the most discerning audiophiles. Whether used individually or as a part of a comprehensive audio system, these amplifiers exemplify the quality that has made Arcam a trusted name in high-fidelity sound.