Arcam P80 manual Using your A80 amplifier, Front panel controls

Page 6

Using your A80 amplifier

SP1

SP2

PROCESSOR

ENTER

 

 

 

SELECT

PHONES

SP1

SP2

AV

TAPE

12 3 4 5 67 8

Front panel controls

This section describes how to operate your amplifier.

If your amplifier has not been installed for you, you should first read the section ‘Installation: A80’ on page 4.

POWER (and power indicator light) bk

Switches the unit on and off. (You can also switch the amplifier into standby mode with the remote control handset.)

The light indicates the status of the amplifier. A red light means the amplifier is in standby mode (press the POWER/STANDBY button on the remote control, or the POWER button on the front panel, to switch between standby and powered-up modes).

When you switch your amplifier on, the light glows amber for a few seconds, during which time the speakers are disconnected. The light changes to green when the amplifier is ready for use.

The light may flash if a fault has occurred – the fault type is shown on the display. You should unplug the amplifier and leave it for a few minutes before reconnecting. If the fault cannot be cleared, unplug your amplifier and contact your Arcam dealer.

Source selectors 9

These buttons select the source connected to the corresponding input.The input currently selected is indicated by text on the display.

AV 4

This input is similar to the other line level inputs on the amplifier and may be used with a VCR or a second recording unit (e.g. cassette deck).

Control knob, SELECT and ENTER 876

The control knob has two functions:

as a volume control, to adjust the output of loudspeakers and headphones connected to the amplifier, and of the pre-amp output (PRE OUT).

when used in conjunction with the SELECT and ENTER buttons, to customise amplifier settings (see page 8).

A80/P80

A80 AMPLIFIER

PHONO

CD

TUNER

AUX

DVD

POWER

9 bk

Volume control settings

It is important to realise that the position of the Control knob is not an accurate indication of the power delivered to your loudspeakers. The amplifier often delivers its full power before the volume control reaches its maximum position, particularly when listening to heavily recorded compact discs. However the amplifier also has to be capable of giving full power output from much lower level sources, such as tuners and cassette decks. Using these sources, the volume control setting may be much higher before distortion (audible overload) sets in. To compensate for this, the input levels of each source may be individually adjusted to avoid accidental overload (see page 8).

SP1 and SP2 2

These buttons allow you to select and deselect the main (SP1) and secondary (SP2) set of speakers attached to your amplifier.

The light above each button glows if the corresponding speakers are currently selected. If both lights are out the amplifier will appear not to work, as all speakers are switched off!

PHONES 1

This socket accepts headphones with an impedance rating between 8Ω and 2kΩ, fitted with a 1/4-inch stereo jack plug. If you wish to listen on headphones only, use the SP1 and SP2 buttons (if necessary) to mute the speakers. The headphone socket is always active.

Remote control receiver 3

The remote control’s infrared receiver is positioned between the SP1/SP2 and PROCESSOR indicator lights on the left-hand side of the front panel window. Ensure the receiver is in a clear line of sight from the remote control to allow signals to be received.

6

Image 6
Contents A80 P80 Safety guidelines Important safety instructionsSafety compliance Using this handbook SafetyContents Connecting to a power supply Installation A80 amplifierConnecting to loudspeakers Positioning the unitPre/power amplifier connections Different output typesUsing your A80 amplifier Front panel controlsRecording Tape-to-tape copying dubbingTo their factory defaults Setting up your A80 amplifierAdjusting listening settings Menu mapUsing the remote control CR-389 Remote ControlInstallation P80 power amplifer Connecting to power, loudspeakers and other equipmentRemote switching Using your P80 power amplifier Power and power indicator lightBi-wiring and bi-amping loudspeakers Bi-wiring your loudspeakersBefore you start Service information Technical specificationsRemote-control codes Guarantee On-line registrationConsignes de sécurité Normes de sécuritéRespect des consignes de sécurité Table des matières Utilisation de ce manuelSécurité DépannageInstallation A80 integrated amplifier Mise en place de l’appareilBranchement des haut-parleurs Alimentation de veille Branchement sur d’autres appareilsBranchement Connexions préamplificateur/amplificateur de PuissanceCommandes du panneau avant Utilisation de l’amplificateur intégré A80Enregistrement Utilisation du bouton TapeRéglage de l’amplificateur intégré A80 IntroductionRéglage des paramètres d’écoute Utilisation de la télécommande Télécommande CR-389Installation amplificateur de puissance P80 Arrêt et mise en marche à l’aide de la télécommandeDétection du signal Power et voyant lumineux d’alimentation Utilisation de l’amplificateur de puissance P80Avant de commencer Bi-câblage des haut-parleursDépannage Spécifications techniquesTableau des commandes IR Garantie Inscription en ligneSicherheitsrichtlinien SicherheitsrichtlinienEinhaltung von Sicherheitsbestimmungen Hinweise zum Handbuch SicherheitInhalt Anschließen der Lautsprecher Installation Vollverstärker A80Aufstellen des Gerätes Anschließen der StromversorgungStandby-Betrieb Anschließen anderer GeräteAnschließen Vorverstärker/EndstufenanschlüsseBedienung des Vollverstärkers A80 Steuerelemente an der VorderseiteAufnahme Empfänger für die FernbedienungEinführung Maximum ‘On’ Volume Mit dem Hauptregler können Sie beimEinstellen des Vollverstärkers A80 Anpassung der HöreinstellungenModell CR-389 UP und DownTasten zum Auswählen der Audioquelle Fernschaltung Installation Endstufe P80Signalerkennung Indem Sie eine Verbindung vom Remote IN-Anschluss derBedienung der Endstufe P80 Bi-Wiring und Bi-Amping der Lautsprecher Bi-Wiring der LautsprecherErste Schritte Kundendienst Technische DatenTabelle der IR-Befehle Online-Registrierung Veiligheidsrichtlijnen VeiligheidsvoorschriftenVeiligheidsnaleving Op lichtnet, luidsprekers en andere apparatuur VeiligheidInhoudsopgave KlantendienstAansluiten op luidsprekers Installatie geïntegreerde versterker A80De eenheid plaatsen Aansluiting op het lichtnetStandby-modus Aansluiting op andere apparatuurAansluiten Voorversterker-/eindversterkeraansluitingenUw geïntegreerde versterker A80 gebruiken Knoppen aan de voorkantOpnemen Kopiëren van tape naar tape dubbingUw geïntegreerde versterker A80 instellen Luisterinstellingen regelenAfstandsbediening CR-389 Volume en dempenDe afstandsbediening gebruiken Omhoog en OmlaagOp afstand bedienen Installatie eindversterker P80Op lichtnet, luidsprekers en andere apparatuur aansluiten DoorlussenPower en aan-/uitlampje Bediening van uw eindversterker P80Zo voert u bi-wiring van luidsprekers uit Bi-wiring en bi-amping van luidsprekersBi-wiring van uw luidsprekers Voordat u begintKlantendienst Technische specificatiesBronkeuze-instructies Codes op de afstandsbedieningStroomtoevoerinstructies Menunavigatie-instructiesOnline-registratie A80/P80 A80/P80 Telephone +44 01223 Fax +44 01223 Issue

P80, A80 specifications

The Arcam P80 and A80 are two prominent products in the realm of high-fidelity audio, designed to offer audiophiles superior sound quality and a seamless listening experience. Arcam, renowned for its dedication to innovation and excellence, has equipped these models with advanced technologies that elevate their performance.

The Arcam P80 is a robust power amplifier that delivers a remarkable 80 watts per channel into 8 ohms. This powerful amplification ensures that even the most demanding speakers will be driven effortlessly, providing dynamic sound reproduction. One of the standout features of the P80 is its Class G amplification design. This technology enhances efficiency by utilizing multiple output stages, allowing the amplifier to switch between power levels depending on the signal demands. This minimizes distortion and maximizes sound quality, resulting in crystal-clear audio across various frequencies.

Equipped with high-quality components, the P80 employs a toroidal transformer that minimizes electromagnetic interference and optimizes power delivery. This attention to detail translates to a more refined sound, making it an excellent choice for both music enthusiasts and home theater setups. The amplifier also features multiple input options, including both balanced and unbalanced connections, ensuring compatibility with a wide range of audio sources.

On the other hand, the Arcam A80 is an integrated amplifier that combines both preamplifier and power amplifier functionalities into a single unit. With an output of 80 watts per channel into 8 ohms, it shares the P80's commitment to power and performance. The A80 incorporates a high-quality digital-to-analog converter, enhancing the sound quality of digital sources, and features multiple inputs for flexibility when connecting various devices.

The A80 also utilizes a high-grade phono stage for vinyl enthusiasts, enabling users to connect turntables directly and enjoy their favorite records with outstanding fidelity. The design emphasizes simplicity and elegance, with a user-friendly interface and intuitive controls, making it a perfect addition to both contemporary and traditional home audio setups.

In summary, the Arcam P80 and A80 represent the pinnacle of audio engineering, incorporating advanced technologies such as Class G amplification, high-quality DACs, and versatile input options. They deliver an exceptional listening experience, providing power, clarity, and musicality that will satisfy even the most discerning audiophiles. Whether used individually or as a part of a comprehensive audio system, these amplifiers exemplify the quality that has made Arcam a trusted name in high-fidelity sound.