JVC LWT0254-001B-H manual CAM2 Length of stub CAM32 Length of stub, 110 K, Video SWITCHER, etc

Page 10

10 Connections & Installation (continued)

EN

Multi-Drop Communication System (continued)

A system that does not employ the RM-P2580 as the controller.

MEMO

●Be sure to terminate the control signal cable at both ends. The cables (length of stub) connecting pieces of non-terminated equipment (cameras or controllers) must be as short as possible. If the length of stub is too long, control precision may suffer.

CONTROL Cable

CAM1

PROTOCOL(1)	: ON
MACHINE ID	: 01
RX TERM	: ON

CAM2 Length of stub	CAM32 Length of stub	Terminate it with
		110 K.

			CONTROLLER*
PROTOCOL(1)	: ON	PROTOCOL(1)	: ON
MACHINE ID	: 02	MACHINE ID	: 32
RX TERM	: OFF	RX TERM	: OFF
		Coaxial Cable

●An AC 24V power source must be supplied to each camera. (A CAUTIONS)

●Set the TERM switch of the camera connected lastly (CAM1 in the example of the above figure) to ON, and terminate at the controller with a resistance of 110 K.

Set the TERM switches of the other cameras to OFF.

VIDEO SWITCHER, etc.

CAUTIONS

●The AC 24 V power supply must be isolated from the primary line. (ISOLATED POWER ONLY)

●In order to prevent an excessive current flow through the power supply wire or camera due to a short circuit, a fuse must be installed in the power supply line.

Image 10

Contents For Customer Use Model No. TK-C625 Serial No LWT0254-001B-HRisk of Electric Shock Do not Open Safety PrecautionsInformation Important Safeguards Characteristics ContentsOperating Precautions → Refer to Preset positionsZooming operation Name and Function of Parts Setting Switch Ceiling Mount Setting Switch Side CameraMachine ID Machine ID Setting Switch Auxiliary SwitchConnections & Installation Multi-Drop Communication SystemCAM2 Length of stub CAM32 Length of stub Video SWITCHER, etc110 K Point-to-Point Communication System ACable ConnectionsB a pg Terminal side of the Ceiling MountExample connection with an RM-P2580 DuplexSimplex Protocol Switch SettingsSync Machine ID Setting Switch Displayed as ID- LL. CheckMachine ID Installation Remove the Cover Cable ConnectionsMake a hole in the ceiling Connect the cable to this camera Lead the cable through the CoverCable Connecting an RG-59 coaxial cablePolyethylene Mesh Wires Core Wire RatingCable Connect this to the remote control unit RM-P2580Connect to an AC 24 V Supply Within 10 cmAttach the Safety Wire Installing the Ceiling MountFasten the ceiling mount to the ceiling Installing the Camera 20 ENPress and hold the Menu button for 3 seconds Setup ProcedureSetting Up the Camera Using RM-P258021 Press the SET buttonSetting Up the Camera Using RM-P2580 Menu Screen Configuration22 EN Private Mask Mode OFF Camera Function 1 Screen 24 ENCamera Function 2 Screen PAN Limit AF for IRTilt Limit Auto ReturnCamera TITLE/ALARM Screen 26 ENCamera ALC/VIDEO Screen 28 EN Auto PAN/PATROL/TRACE ScreenPOS. Function SET Screen Factory Settings Screen 30 ENPrivate Mask Setup Menu screen display. a pg , steps 2 to Manual PAN Limit SetupSelect a camera. ARM-P2580 Ainstructionsb Set the position for the left limitOperations that override the Manual Pan Limit Settings that override the Manual Pan LimitBasic operation of Manual Pan Limit Right LimitMenu Screen Camera Title SetupTele Numeric Enter Button keys button Wide button Space Blinking Character areaRepeat Steps 5 to Area Display Setup TitlePress the FAR button Menu buttonWest Area Display Setup DirectionEast Camera buttonRepeat steps 5 to 7 for each alarm title Alarm Title SetupCamera buttonNNumeric keyCamera NumberNENTER button Set the end position only when in the Return mode Auto PAN SetupSet the Auto PAN Mode and Auto PAN Speed Select camera. ARM-P2580 AinstructionsbSet a patroll position Auto Patrol SetupChange the Auto Patrol mode Set the length of time a camera will stay in each positionCamera buttonNNumeric key Camera Number Nenter button Auto Trace SetupSet the patrol start position To Start Auto Trace FunctionRepeat steps 5 to 7 for each title character Position Title SetupSelect a preset position. a RM-P2580 Ainstructionsb Position buttonNNumeric key position numberNENTER button42 EN TroubleshootingOther Pan/Tilt Mechanism SpecificationsExternal Dimensions Unit mm GeneralVictor Company of Japan, Limited