Panasonic WV-NP472E Shutter Speed Setting Shutter, Gain Control Setting AGC on DNR-H, DNR-L/OFF

Page 17

2-2. ALC Mode with SUPER-D2 OFF and ELC Mode

Note: If ELC is selected, set MASK SET according to this procedure.

1.Move the cursor to SUPER-D2 and select OFF. (When you select ELC, SUPER-D2 is not available.) MASK SET appears on the menu.

** ALC CONT **

BACK LIGHT COMP

SUPER-D2

 

OFF

 

MASK SET

↵

 

LEVEL

 

...I

 

-

+

RET END

2.Move the cursor to MASK SET and press I. The 48 mask areas appear on the monitor screen. The cursor is blinking in the upper left corner of the screen.

Blinking

3.Move the cursor to the area where backlight is bright and press I to mask that area. The mask turns to white. (When the cursor is moved on an area that has already been masked, the mask and cursor start blinking.)

Blinking

4.Repeat step 3 to mask desired areas. To cancel

masking, move the cursor to that area and press

I.

5.After masking is completed, press I for 2 sec-

onds or more. The ALC CONT menu appears.

6.If you want to change the video output level (pic- ture contrast), move the “I” cursor for LEVEL and adjust the level.

Turns to white

Blinking

Note: If ON is selected for SUPER-D2, a shadow (black line) may appear at the boundary between the bright and the dim scenes. This is a natural phe- nomenon and does not indicate any trouble.

3. Shutter Speed Setting (SHUTTER)

Note: When ELC is selected for ALC/ELC on the CAM SET UP menu or ON is selected for SUPER-D2 on the ALC CONT menu, this item is not available.

To select electronic shutter speed, select OFF for SUPER-D2 in the ALC CONT menu.

Move the cursor to SHUTTER and select the electronic shutter speed.

The preset values for SHUTTER (electronic shutter speed) change by pressing L or M as follows:

The factory default setting is ---.

OFF (1/50) 1/120 1/250 1/500

1/10000

1/4000

 

1/2000

 

1/1000

 

 

4.Gain Control Setting (AGC ON (DNR-H, DNR-L)/OFF)

AGC (Automatic Gain Control) automatically controls the gain (an image brightness level).

Move the cursor to AGC and select automatic level adjustment ON (DNR-H), ON (DNR-L), or OFF. The fac- tory default setting is ON (DNR-H).

ON (DNR-H):This setting raises the gain and brightens the image under low light conditions.

ON (DNR-L):This setting reduces an afterimage sometimes caused by the object's movement.

OFF: This setting does not control the gain.

Notes:

•When ON (DNR-L) is selected, the noise level may be slightly higher than the ON (DNR-H) mode.

•DNR-H and DNR-L do not appear on the system status display of the connected equipment.

-17-

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operating Instructions Risk of Electric Shock Do not Open Contents TCP/IP, HTTP, FTP, SMTP, DNS, Dhcp PrefaceClean the CCD faceplate with care PrecautionsHandle the camera with care Never face the camera toward the sunMajor Operating Controls and Their Functions Mounting the Lens Notes InstallationsReplacement of Auto Iris Lens Connector Mounting from the Bottom Flange-back AdjustmentMounting from the Top Pictures Upside-downConnections Power-in ConnectionsControl Terminal Connections Video Cable ConnectionsConnection to Internet Type Connection to Intranet TypeOperating the Camera Access from the PCPreliminary Setup Function Comparison / PC Network vs. Camera site Access from the Camera/System DeviceNetwork Speed Select a speed Buttons Used for Setup Menus Prior to SET UPCamera Setup Menus ¡From the PC¡From the Camera Camera Identification Camera ID Setting Setting ProceduresALC Mode with SUPER-D2 on Light Control Setting ALC/ELCALC Mode with SUPER-D2 OFF and ELC Mode Shutter Speed Setting ShutterGain Control Setting AGC on DNR-H, DNR-L/OFF Auto-Tracing White Balance Mode ATW White Balance Setting White BALElectronic Sensitivity Enhancement Sens UP ATW1 Auto-Tracing White BalanceLens Drive Signal Selection Lens Drive Motion Detector Setting Motion DETDate Display Clock Setting Manual Fine Adjustment for AWC ATWSpecial Menu Http Port Number To reset to the factory settings Camera ResetConnections SET UP from the PCConnection to Internet Type Connection to Intranet TypeNetwork Setup of the PC Network Setup of the Camera Connection type Description of the parameter Network Setup Parameters vs. Connection TypeDNS DhcpSet to on when using the DNS server Set to on if your internet Internet service provider uses a Set to on if the router uses Dhcp Day & Night Mode Setup buttons ON/OFF/AUTO Setup Menu buttonReset button ALL Reset Return buttonCamera Setup Menus Image Capture Size pixels 752x568*, 752x280, 368x280 PC Oriented SET UPAlarm Setup Image Setup FTP Client Setup User Setup System Setup Host SetupInitializing Initializing the Setup MenuInitializing the Camera Menu Initializing Html FilesImage Capture Size pixels 752x568 Viewing PicturesImage Quality Selection Monochrome Mode Transferring Picture Files Alarm FunctionsWhen an Alarm Arises VMD Setup Canceling Alarm DisplayDetection Area Setup EnterReviewing Alarm Pictures Resetting Alarm Auxiliary Output Control Auxiliary Output ControlTroubleshooting General SpecificationsNetwork Section Camera SectionOptional Accessories Standard Accessories2003
Top Page Image Contents