Panasonic WV-NP472E operating instructions Major Operating Controls and Their Functions

Page 6

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

q w e

WV –NP472

r

u

i t

yo

Slide the panel to the left until it locks.

qAuto Iris Lens Connector

Connects the auto iris lens with a 4-pin male con- nector supplied as a standard accessory (Part No. YFE4191J100).

wFlange-back Adjusting Ring & Screw

Adjusts the back focal length and picture focus.

eLens (Option)

rCamera Mounting Adapter

Mounts the camera onto a mounting bracket.

tDown Button (K)

Moves the cursor downward and selects items in the CAM SET UP menu.

yLeft Button (L)

Moves the cursor leftward, selects the mode and adjusts some levels.

uUp Button (J)

Moves the cursor upward and selects items in the CAM SET UP menu.

i Right Button (M)

Moves the cursor rightward, selects the mode and adjusts some levels.

oSet Button (I)

Activates an item selected in the CAM SET UP menu.

-6-

	!1	!2		!3
	ALARM IN
	ALARM OUT
	AUX OUT
	DAY/NIGHT IN
	GND	A	B
			VIDEO OUT
	RCV		DC 12V	POWER
	RCV		IN
!0	10BASE-T/			!4
!0	100BASE-TX			!4
	LINK

!0Network Port with Indicators (10BASE-T/ 100BASE-TX/RCV/LINK)

Connects to a PC or a network via a hub with a 10BASE-T/100BASE-TX cable attached RJ-45 con- nector. Indicators will light up while receiving data (RCV) or establishing communications (LINK).

!1Control Terminals

Connects respective devices.

ALARM IN: Alarm sensor, ALARM OUT: Recording

device/alarm indicator, AUX OUT: External device,

DAY/NIGHT IN: Optical sensor, GND: Signal ground

!2Reset Button (A, B)

The button A, along with the J and K buttons, resets the network setup parameters when you hold down these buttons for 6 seconds in the power-on state.

The button B resets the HTML files and alarm mail setup in the same manner as the button A.

Note: Never press both the reset buttons A and B at a time.

!3Video Output Connector (VIDEO OUT)

Supplies analog video signal (composite) to the connected device.

!4Power In Terminal and Power Indicator (DC 12V IN, POWER)

Connects to a DC power supply using proper cables. The power indicator lights up when power is supplied.

Image 6

Contents Operating Instructions Risk of Electric Shock Do not Open Contents Preface TCP/IP, HTTP, FTP, SMTP, DNS, DhcpHandle the camera with care PrecautionsClean the CCD faceplate with care Never face the camera toward the sunMajor Operating Controls and Their Functions Installations Replacement of Auto Iris Lens ConnectorMounting the Lens Notes Mounting from the Top Flange-back AdjustmentMounting from the Bottom Pictures Upside-downControl Terminal Connections Power-in ConnectionsConnections Video Cable ConnectionsConnection to Intranet Type Connection to Internet TypeAccess from the PC Preliminary SetupOperating the Camera Access from the Camera/System Device Network Speed Select a speedFunction Comparison / PC Network vs. Camera site Camera Setup Menus Prior to SET UPButtons Used for Setup Menus ¡From the PC¡From the Camera Setting Procedures Camera Identification Camera ID SettingLight Control Setting ALC/ELC ALC Mode with SUPER-D2 onShutter Speed Setting Shutter Gain Control Setting AGC on DNR-H, DNR-L/OFFALC Mode with SUPER-D2 OFF and ELC Mode Electronic Sensitivity Enhancement Sens UP White Balance Setting White BALAuto-Tracing White Balance Mode ATW ATW1 Auto-Tracing White BalanceDate Display Clock Setting Motion Detector Setting Motion DETLens Drive Signal Selection Lens Drive Manual Fine Adjustment for AWC ATWSpecial Menu To reset to the factory settings Camera Reset Http Port NumberConnection to Internet Type SET UP from the PCConnections Connection to Intranet TypeNetwork Setup of the PC Network Setup of the Camera DNS Network Setup Parameters vs. Connection TypeConnection type Description of the parameter DhcpSet to on when using the DNS server Set to on if your internet Internet service provider uses a Set to on if the router uses Dhcp Reset button ALL Reset Setup Menu buttonDay & Night Mode Setup buttons ON/OFF/AUTO Return buttonCamera Setup Menus PC Oriented SET UP Alarm Setup Image SetupImage Capture Size pixels 752x568*, 752x280, 368x280 FTP Client Setup User Setup Host Setup System SetupInitializing the Camera Menu Initializing the Setup MenuInitializing Initializing Html FilesViewing Pictures Image Quality SelectionImage Capture Size pixels 752x568 Monochrome Mode Alarm Functions When an Alarm ArisesTransferring Picture Files Detection Area Setup Canceling Alarm DisplayVMD Setup EnterReviewing Alarm Pictures Resetting Alarm Auxiliary Output Control Auxiliary Output ControlTroubleshooting Network Section SpecificationsGeneral Camera SectionStandard Accessories Optional Accessories2003