Panasonic WV-NP472E operating instructions User Setup

Page 33

2.Common Setup

•Enter the FTP server address.

A hostname.domainname can be entered when using the DNS function.

•Enter the user name with a maximum of 16 characters.

•Enter the password with a maximum of 16 characters.

•Select a transmission mode from Sequential or Passive. Passive is recommended when Sequential does not perform properly.

•Complete the schedule 1 and 2, by specifying the transmission time zone and the day of a week.

3.None Alarm (FTP) Image Transmission Setup

•Select ON or OFF to transmit ordinary image files except during an alarm event.

ON: Transmits files when a scheduled time comes.

OFF: Does not transmit, and no schedule is applied.

•Enter a receiver directory.

•Enter a file name and click a radio button.

Fix: Uses repeatedly a single file name when overwriting new data.

Date & Time: Creates and attaches a serial number and a date-and-time to the entered file name.

•Set a transmission interval.

Available time (seconds): 0.2 - 0.9, 1 - 1 440

Available time (minutes): 1 - 1 440

Notes:

•Transmission interval may be delayed depend- ing on the network speed and/or traffic condi- tions.

•The alarm image precedes the non-alarm image in transmission to the FTP server. The non-alarm image may not be sent when alarm activations frequently arise.

4.Alarm (FTP) Image Transmission Setup

The alarm setup window specifies the profile of the transmitting files such as the numbers of files and the frame rate (fps).

•Select ON or OFF to transmit the image files. ON: Transmits the files when an alarm oper-

ates.

OFF: Does not transmit.

•Enter a receiver directory.

•Enter a file name.

5.Click the SET & REBOOT button.

6.Click the Return button to go back to the main page.

■User Setup

1.Open the User Setup window.

2.User Registration

•Enter to 16 characters of user name. The default setting is “admin”.

•Enter a password. The default setting is a blank.

•Enter a password again.

•Select an access level, and click the SET but- ton.

1(Administrator): Allows you to operate setup menus and to view live and record- ed images.

2(Live Only): Allows you to view live and recorded images.

3.User Authentication

•Select ON or OFF, and click the SET button. ON: applies the user authentication.

OFF: does not apply.

•Click the Delete button after selecting an unwanted user name to cancel it.

Note: You cannot change admin and level 1 that are registered as the default settings while the password entry is allowed.

-33-

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Operating Instructions Risk of Electric Shock Do not Open Contents TCP/IP, HTTP, FTP, SMTP, DNS, Dhcp PrefaceClean the CCD faceplate with care PrecautionsHandle the camera with care Never face the camera toward the sunMajor Operating Controls and Their Functions Installations Replacement of Auto Iris Lens ConnectorMounting the Lens Notes Mounting from the Bottom Flange-back AdjustmentMounting from the Top Pictures Upside-downConnections Power-in ConnectionsControl Terminal Connections Video Cable ConnectionsConnection to Internet Type Connection to Intranet TypeAccess from the PC Preliminary SetupOperating the Camera Access from the Camera/System Device Network Speed Select a speedFunction Comparison / PC Network vs. Camera site Buttons Used for Setup Menus Prior to SET UPCamera Setup Menus ¡From the PC¡From the Camera Camera Identification Camera ID Setting Setting ProceduresALC Mode with SUPER-D2 on Light Control Setting ALC/ELCShutter Speed Setting Shutter Gain Control Setting AGC on DNR-H, DNR-L/OFFALC Mode with SUPER-D2 OFF and ELC Mode Auto-Tracing White Balance Mode ATW White Balance Setting White BALElectronic Sensitivity Enhancement Sens UP ATW1 Auto-Tracing White BalanceLens Drive Signal Selection Lens Drive Motion Detector Setting Motion DETDate Display Clock Setting Manual Fine Adjustment for AWC ATWSpecial Menu Http Port Number To reset to the factory settings Camera ResetConnections SET UP from the PCConnection to Internet Type Connection to Intranet TypeNetwork Setup of the PC Network Setup of the Camera Connection type Description of the parameter Network Setup Parameters vs. Connection TypeDNS DhcpSet to on when using the DNS server Set to on if your internet Internet service provider uses a Set to on if the router uses Dhcp Day & Night Mode Setup buttons ON/OFF/AUTO Setup Menu buttonReset button ALL Reset Return buttonCamera Setup Menus PC Oriented SET UP Alarm Setup Image SetupImage Capture Size pixels 752x568*, 752x280, 368x280 FTP Client Setup User Setup System Setup Host SetupInitializing Initializing the Setup MenuInitializing the Camera Menu Initializing Html FilesViewing Pictures Image Quality SelectionImage Capture Size pixels 752x568 Monochrome Mode Alarm Functions When an Alarm ArisesTransferring Picture Files VMD Setup Canceling Alarm DisplayDetection Area Setup EnterReviewing Alarm Pictures Resetting Alarm Auxiliary Output Control Auxiliary Output ControlTroubleshooting General SpecificationsNetwork Section Camera SectionOptional Accessories Standard Accessories2003
Top Page Image Contents