Panasonic WV-NP472E Set to on if your internet Internet service provider uses a

Page 27

 

Secondary server

Set the IP address of DNS when using the DNS server.

 

 

Refer to your internet Internet service provider for the IP

 

 

address of the DNS. Primary and secondary IP addresses

 

 

can be set for the DNS.

 

 

 

 

DHCP

Set to ON if your internet Internet service provider uses a

 

 

DHCP server (the DHCP server assigns an IP address to the

 

 

camera automatically) after confirming that your internet

 

 

Internet service provider uses a DHCP server.

 

 

 

Connection type 4

IP address

The setting differs depending on the setting of the router as

 

 

follows.

 

 

If the router uses DHCP: No setting required

 

 

If the router does not use DHCP: Assignment of a private IP

 

 

address to the router is required. However, the IP addresses

 

 

already assigned to the PC and other cameras are not avail-

 

 

able.

 

 

For further information, refer to the operating instructions of

 

 

the router.

 

 

 

 

Subnet mask

The setting differs depending on the setting of the router as

 

 

follows.

 

 

If the router uses DHCP: No setting required

 

 

If the router does not use DHCP: Setting of the subnet mask

 

 

is required.

 

 

For further information, refer to the operating instructions of

 

 

the router.

 

 

 

 

Default gateway

The setting differs depending on the setting of the router as

 

 

follows.

 

 

If the router uses DHCP: No setting required

 

 

If the router does not use DHCP: Assignment of an IP

 

 

address to the router is required.

 

 

For further information, refer to the operating instructions of

 

 

the router.

 

 

 

 

Network speed

Set the network speed.

 

 

Use the default setting “auto” for the network speed.

 

 

Selectable parameters: auto (default setting), 100 Mbps (full

 

 

duplex), 100 Mbps (half duplex), 10 Mbps (full duplex), 10

 

 

Mbps (half duplex)

 

 

 

 

HTTP port

If multiple cameras are connected, it is required to set up

 

 

each camera individually.

 

 

However, the port numbers already assigned to other hard-

 

 

ware are not available.

 

 

The following are already assigned to the camera.

 

 

Port number: 20, 21, 23, 25, 53, 67, 38, 80, 546, 547

 

 

The following are not usable if the FTP client function is set to

 

 

on.

 

 

Port number: from 4000 to 5000

 

 

The following is not usable if the custom alarm function is set

 

 

to on.

 

 

Port number: number already assigned to the custom

 

 

alarm.

 

 

 

-27-

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Operating Instructions Risk of Electric Shock Do not Open Contents TCP/IP, HTTP, FTP, SMTP, DNS, Dhcp PrefaceNever face the camera toward the sun PrecautionsClean the CCD faceplate with care Handle the camera with careMajor Operating Controls and Their Functions Installations Replacement of Auto Iris Lens ConnectorMounting the Lens Notes Pictures Upside-down Flange-back AdjustmentMounting from the Bottom Mounting from the TopVideo Cable Connections Power-in ConnectionsConnections Control Terminal ConnectionsConnection to Internet Type Connection to Intranet TypeAccess from the PC Preliminary SetupOperating the Camera Access from the Camera/System Device Network Speed Select a speedFunction Comparison / PC Network vs. Camera site ¡From the PC Prior to SET UPButtons Used for Setup Menus Camera Setup Menus¡From the Camera Camera Identification Camera ID Setting Setting ProceduresALC Mode with SUPER-D2 on Light Control Setting ALC/ELCShutter Speed Setting Shutter Gain Control Setting AGC on DNR-H, DNR-L/OFFALC Mode with SUPER-D2 OFF and ELC Mode ATW1 Auto-Tracing White Balance White Balance Setting White BALAuto-Tracing White Balance Mode ATW Electronic Sensitivity Enhancement Sens UPManual Fine Adjustment for AWC ATW Motion Detector Setting Motion DETLens Drive Signal Selection Lens Drive Date Display Clock SettingSpecial Menu Http Port Number To reset to the factory settings Camera ResetConnection to Intranet Type SET UP from the PCConnections Connection to Internet TypeNetwork Setup of the PC Network Setup of the Camera Dhcp Network Setup Parameters vs. Connection TypeConnection type Description of the parameter DNSSet to on when using the DNS server Set to on if your internet Internet service provider uses a Set to on if the router uses Dhcp Return button Setup Menu buttonDay & Night Mode Setup buttons ON/OFF/AUTO Reset button ALL ResetCamera Setup Menus PC Oriented SET UP Alarm Setup Image SetupImage Capture Size pixels 752x568*, 752x280, 368x280 FTP Client Setup User Setup System Setup Host SetupInitializing Html Files Initializing the Setup MenuInitializing Initializing the Camera MenuViewing Pictures Image Quality SelectionImage Capture Size pixels 752x568 Monochrome Mode Alarm Functions When an Alarm ArisesTransferring Picture Files Enter Canceling Alarm DisplayVMD Setup Detection Area SetupReviewing Alarm Pictures Resetting Alarm Auxiliary Output Control Auxiliary Output ControlTroubleshooting Camera Section SpecificationsGeneral Network SectionOptional Accessories Standard Accessories2003
Top Page Image Contents