Panasonic WV-NP472E operating instructions FTP Client Setup

Page 32

1.Open the Alarm Setup window.

2.External Alarm

•Select ON or OFF, and click the SET button. ON: Receives alarm inputs via the ALARM IN

terminal.

OFF: Ignores alarm inputs via the ALARM IN terminal.

3.E-Mail Notice Setup

•Select ON or OFF for E-mail Notice.

ON: Sends an e-mail when an alarm operates.

OFF: Does not send.

•Enter the e-mail server address.

A hostname.domainname can be entered when using the DNS function.

•Enter the sender name. The default setting is NW_camera.

•Select ON or OFF for Attach Image.

ON: Attaches the image data to an e-mail.

OFF: Does not attach.

•Click the SET & REBOOT button.

•Enter a maximum of 4 destination addresses, and click the SET button.

•Click the DEL (delete) button after selecting an unwanted destination to cancel it.

4.Recording Setup

The image fields are stored before and after the alarm input in the memories of the camera.

•Set the image frame numbers for the pre recording (0 - 10) and post recording (1 - 20).

•Set the recording rate (fps: frame per second).

Rates for Before: 1/10, 1/5, 1/3, 1/2, 1, 2, 3.3, 5

Rates for After: 1/10, 1/5, 1/3, 1/2, 1, 2, 3.3, 5, 10

•Click the SET & REBOOT button.

5.Panasonic Protocol Setup

•Select ON or OFF.

ON: Sends alarm notice mails to the cus- tomized destinations.

OFF: Does not send.

•Enter the destination port. The port number is exclusively assigned to this function, and any other usage is not allowed.

•Enter the retry times from 1 to 25.

•Click the SET button.

-32-

•Enter a maximum of 8 destination IP address- es, and click the SET button.

•Click the DEL (delete) button after selecting an unwanted destination to cancel it.

6.External Terminal Output Setup

The alarm output is supplied from the terminal on the rear of the camera.

•Select a signal type that the connected device accepts.

Pulse: Holds active status during the specified time width.

Latch: Holds active status until it is reset man- ually.

•Enter pulse width (n x 100 milli-seconds) if you selected Pulse. A number from 1 to 100 is allowed.

•Click the SET & REBOOT button.

7.Alarm Reset

•Click the ALARM RESET button to cancel the activated alarm.

■FTP Client Setup

Image files can be transferred to the FTP server within the scheduled time zone.

1. Open the FTP Client Setup window.

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Operating Instructions Risk of Electric Shock Do not Open Contents Preface TCP/IP, HTTP, FTP, SMTP, DNS, DhcpPrecautions Clean the CCD faceplate with careHandle the camera with care Never face the camera toward the sunMajor Operating Controls and Their Functions Mounting the Lens Notes InstallationsReplacement of Auto Iris Lens Connector Flange-back Adjustment Mounting from the BottomMounting from the Top Pictures Upside-downPower-in Connections ConnectionsControl Terminal Connections Video Cable ConnectionsConnection to Intranet Type Connection to Internet TypeOperating the Camera Access from the PCPreliminary Setup Function Comparison / PC Network vs. Camera site Access from the Camera/System DeviceNetwork Speed Select a speed Prior to SET UP Buttons Used for Setup MenusCamera Setup Menus ¡From the PC¡From the Camera Setting Procedures Camera Identification Camera ID SettingLight Control Setting ALC/ELC ALC Mode with SUPER-D2 onALC Mode with SUPER-D2 OFF and ELC Mode Shutter Speed Setting ShutterGain Control Setting AGC on DNR-H, DNR-L/OFF White Balance Setting White BAL Auto-Tracing White Balance Mode ATWElectronic Sensitivity Enhancement Sens UP ATW1 Auto-Tracing White BalanceMotion Detector Setting Motion DET Lens Drive Signal Selection Lens DriveDate Display Clock Setting Manual Fine Adjustment for AWC ATWSpecial Menu To reset to the factory settings Camera Reset Http Port NumberSET UP from the PC ConnectionsConnection to Internet Type Connection to Intranet TypeNetwork Setup of the PC Network Setup of the Camera Network Setup Parameters vs. Connection Type Connection type Description of the parameterDNS DhcpSet to on when using the DNS server Set to on if your internet Internet service provider uses a Set to on if the router uses Dhcp Setup Menu button Day & Night Mode Setup buttons ON/OFF/AUTOReset button ALL Reset Return buttonCamera Setup Menus Image Capture Size pixels 752x568*, 752x280, 368x280 PC Oriented SET UPAlarm Setup Image Setup FTP Client Setup User Setup Host Setup System SetupInitializing the Setup Menu InitializingInitializing the Camera Menu Initializing Html FilesImage Capture Size pixels 752x568 Viewing PicturesImage Quality Selection Monochrome Mode Transferring Picture Files Alarm FunctionsWhen an Alarm Arises Canceling Alarm Display VMD SetupDetection Area Setup EnterReviewing Alarm Pictures Resetting Alarm Auxiliary Output Control Auxiliary Output ControlTroubleshooting Specifications GeneralNetwork Section Camera SectionStandard Accessories Optional Accessories2003
Top Page Image Contents