Panasonic AK-HC1500G Gen-Lock, PIX Defect, GEN-LOCK Input BNC, Dsub, Auto Detection

Page 42

Setting of menu items

SETTING menu

[3]GEN-LOCK

��GEN-LOCK ��
GEN-LOCK INPUT	:BNC
H PHASE-COARSE	:+00
H PHASE-FINE	:+000
SD HD PHASE CRS	:+0
SD HD PHASE FINE	:+00

[4] PIX DEFECT

��PIX DEFECT ��

AUTO DETECTION

:READY

CNT

R1

G5

B2

Y1

GEN-LOCK INPUT [BNC, DSUB]

For selecting whether the sync signals are to be input from the BNC or D-SUB connector.

HPHASE-COARSE [–40 to +40 (720 mode)] [–60 to +60 (1080 mode)]

For roughly adjusting the horizontal phase.

HPHASE-FINE [–45 to +45]

For finely adjusting the horizontal phase.

SD  HD PHASE CRS [–4 to +4]

For roughly adjusting the phase of the HD video signals when SD sync signals have been input.

SD  HD PHASE FINE [–99 to +99]

For finely adjusting the phase of the HD video signals when SD sync signals have been input.

AUTO DETECTION

When ACTIVE is selected, automatic defect compensation processing* is performed, and when this processing is completed, the status returns to READY.

*Execute automatic defect compensation processing after supplying the power to the camera at the normal temperature for at least two hours.

- 41 (E) -

Image 42

Contents AK-HC1500G Multi Purpose CameraEnglish Version FCC NoteEnglish Important Safety Instructions For business users in the European Union Contents AccessoriesCharacteristics IntroductionPrecautions for use  Cooling fanFront view Bottom view Rear viewMajor operating controls and their functions  HD SDI output connector HD SDI OUT  Tally output connector Tally OUT How to set the lens Iris control cable to Iris connectorHow to set up the system Configuration example 1 Connection of camera controllerConfiguration example 2 High-Speed P/T system Adjust the black balance Operation procedureAdjust the white balance Start shootingLens iris gain volume adjustment How to adjustFlange back adjustment for zoom lens Auto iris power zoom lensWhite balance adjustment Color temperature and white balance adjustment referenceBlack balance adjustment Gen-lock adjustment Using AK-HRP150G camera controller Setting of menu itemsHow to display the menus TOP menuDetection READY, Active  Maintenance menuBlack Shading Correctdig OFF, onPEDESTAL, Gamma GammaDRS OFF, on Gamma OFF, onBlack Gamma OFF, on Cine Gamma Select Video REC, Film RECFlare Flare 000 toFlare OFF, on 80.00% to 107.00% Video Menu 30% to 90% Film MENU/VIDEO REC KNEE, White ClipKnee Point Knee Point -25.00% to +25.00%Knee Point 80.00% to 107.00% Knee Level 100% to 109%White Clip LVL 90% to 109% White Clip OFF, on B GainKnee OFF, MANUAL, Auto High Color OFF, onDetail Detail OFF, onKnee Aperture OFF, on Slim Detail OFF, on Detail SourceSkin Tone Detail Skin Tone DTL OFF, onSkin GET OFF, on Iris Level 0 to Iris Mode LENS, CAMGAIN, Auto Iris Iris PEAK/AVE 0 toMode S.GAIN1, S.GAIN2, S.GAIN3 Super GainPeak Frequency 0 to 35 to 0.75 DRS OFF -10 to +10 DRS onPED Offset -200 to +200 Frame Mode Frame Rate Range 60-6Frame Rate 60 to Matrix Matrix Table A, BColor Correction Gain Select  Setting menuMode LOW, MID, HIGH, S.GAIN1 toDigital Extender OFF, on Matrix Table OFF, A, BColor Correction OFF, on BAR SELAWB Active FormatStatus OFF, on AWB OKMenu on BAR OFF, on ABB OKOUT Range RGB FAN OFF, AUTO, onShutter Shutter SpeedSynchro Scan GEN-LOCK Input BNC, Dsub GEN-LOCKPIX Defect Auto DetectionProtocol Protocol 1 to Camera ID menu LOAD/STORE from Mode LOAD/STORE File Operation menu ExecuteReset Preset Time Code menu Menu list 47 E 48 E Appearance Unit inch mmSpecifications Input/output signalAppendix Control cable for information camera