Panasonic AK-HC1500G operating instructions Black balance adjustment, Gen-lock adjustment

Page 19

How to adjust

Black balance adjustment

Adjust it with the lens closed.

When the motor drive lens is controlled from the camera, adjusting the black balance causes the lens to be automatically closed.

Gen-lock adjustment

When multiple cameras are used or the camera is combined with other equipment, it is necessary to adjust the phase for phase matching by external synchronization.

Horizontal phase adjustment

Observe the waveforms of externally synchronizing signal input (black burst signal) and video signal output by a two-phenomenon oscilloscope, and make the horizontal phase according to the camera menu.

Adjustment with GEN-LOCK of SETTING menu

When HD synchronizing signals are input:

Roughly adjust the synchronizing signal input and video signal output phases by

H PHASE-COARSE.

Finely adjust the synchronizing signal input and video signal output phases by

H PHASE-FINE.

�� GEN-LOCK ��
GEN-LOCK INPUT		:BNC
H	PHASE-COARSE	:+00
H	PHASE-FINE	:+000

When SD synchronizing signals are input:

Roughly adjust the synchronizing signal input and video signal output phases by SD-

HD PHASE-COARSE.

Finely adjust the synchronizing signal input and video signal output phases by SD-HD PHASE-FINE. If the adjustment performed using SD-HD PHASE is not satisfactory, use H PHASE-COARSE/FINE.

��GEN-LOCK ��
GEN-LOCK INPUT	:BNC
H PHASE-COARSE	:+00
H PHASE-FINE	:+000
SD HD PHASE CRS	:+0
SD HD PHASE FINE	:+00

ENGLISH

- 18 (E) -

Image 19

Contents Multi Purpose Camera AK-HC1500GFCC Note English VersionEnglish Important Safety Instructions For business users in the European Union Accessories ContentsIntroduction Characteristics Cooling fan Precautions for useBottom view Rear view Front viewMajor operating controls and their functions  HD SDI output connector HD SDI OUT  Tally output connector Tally OUT Iris control cable to Iris connector How to set the lensConfiguration example 1 Connection of camera controller How to set up the systemConfiguration example 2 High-Speed P/T system Start shooting Operation procedureAdjust the white balance Adjust the black balanceAuto iris power zoom lens How to adjustFlange back adjustment for zoom lens Lens iris gain volume adjustmentColor temperature and white balance adjustment reference White balance adjustmentGen-lock adjustment Black balance adjustmentTOP menu Setting of menu itemsHow to display the menus  Using AK-HRP150G camera controllerCorrectdig OFF, on  Maintenance menuBlack Shading Detection READY, ActiveGamma PEDESTAL, GammaCine Gamma Select Video REC, Film REC Gamma OFF, onBlack Gamma OFF, on DRS OFF, onFlare 000 to FlareFlare OFF, on Knee Point -25.00% to +25.00% KNEE, White ClipKnee Point 80.00% to 107.00% Video Menu 30% to 90% Film MENU/VIDEO RECKnee Level 100% to 109% Knee Point 80.00% to 107.00%White Clip LVL 90% to 109% High Color OFF, on B GainKnee OFF, MANUAL, Auto White Clip OFF, onDetail OFF, on DetailKnee Aperture OFF, on Detail Source Slim Detail OFF, onSkin Tone DTL OFF, on Skin Tone DetailSkin GET OFF, on Iris PEAK/AVE 0 to Iris Mode LENS, CAMGAIN, Auto Iris Iris Level 0 toSuper Gain Mode S.GAIN1, S.GAIN2, S.GAIN335 to 0.75 DRS OFF -10 to +10 DRS on Peak Frequency 0 toPED Offset -200 to +200 Frame Rate Range 60-6 Frame ModeFrame Rate 60 to Matrix Table A, B MatrixColor Correction LOW, MID, HIGH, S.GAIN1 to  Setting menuMode Gain SelectBAR SEL Matrix Table OFF, A, BColor Correction OFF, on Digital Extender OFF, onAWB OK FormatStatus OFF, on AWB ActiveFAN OFF, AUTO, on ABB OKOUT Range RGB Menu on BAR OFF, onShutter Speed ShutterSynchro Scan Auto Detection GEN-LOCKPIX Defect GEN-LOCK Input BNC, DsubProtocol 1 to Protocol Camera ID menu Execute Mode LOAD/STORE File Operation menu LOAD/STORE fromPreset Reset Time Code menu Menu list 47 E 48 E Unit inch mm AppearanceInput/output signal SpecificationsControl cable for information camera Appendix