Panasonic WV-SW598 Do not damage the power cable, Correctly perform all wiring

Page 10

Do not damage the power cable.

Do not damage, fabricate, twist, stretch, bundle, or forci- bly bend the power cable. Do not place heavy objects on it, and keep it away from heat sources.

Use of a damaged power cable may cause electric shock, short circuit, or fire.

Consult the dealer for repair.

Do not install this product on a place that is greatly influenced by wind.

Installation on a place where the wind speed is 40 m {131.23 feet} or more per second may cause a fall of the product resulting in injury or accidents.

The measures of protection against snowfall shall be taken.

Weight of snow may cause a fall of the product resulting in injury or accidents.

Protect the product against snowfall by installing it under eaves.

Correctly perform all wiring

Short circuits in the wiring or incorrect wiring may cause fire or electrical shock.

Turn the power off when cleaning this product.

Failure to observe this may cause injury.

[Precautions for use]

This product has no power switch.

When turning off the power, disconnect the power supply from the 24 V AC power supply or the PoE+ device.

To keep on using with stable performance

Do not use this product in hot and humid conditions for a long time. Failure to observe this causes component deg- radation resulting in life shortening of this product.

Do not expose this product to direct heat sources such as a heater.

Handle this product with care.

Do not drop this product, nor apply shock or vibration to the product. Failure to observe this may cause trouble.

Do not give a strong shock to the dome cover. It may cause damage or water exposure.

About the PC monitor

When displaying the same image on the PC monitor for a long time, the PC monitor may be damaged.

It is recommended to use a screen-saver.

When an error is detected, this product will restart automatically.

This product will be inoperable for around 2 minutes after the restart just as when the power is turned on.

Product disposal/transfer

Data saved on this product or a storage device used with this product may lead to personal information leakage. When it is necessary to dispose or give this product to someone, even when for repair, make sure that there is no data on this product.

Do not touch the dome cover with your bare hands. The rain wash coating is applied to the surface of the dome cover. Do not directly touch the surface of the dome cover or wipe it with a cloth or other product. Failure to observe this may reduce the effectiveness of the rain wash coating.

Cleaning this product body

Be sure to turn off the power before cleaning.

When cleaning the dome cover, wash away any dirt or other unwanted substances by pouring or spraying clean water from a hose or spray bottle (do not wipe the dome cover with a cloth or other product). Do not use benzine, thinner, alcohol, or any other types of solvents or detergents.

When cleaning areas other than the dome cover, do not use benzine, thinner, or any other types of sol- vents. Failure to observe this may cause discoloration. When using a chemical cloth for cleaning, read the caution provided with the chemical cloth product.

IMPORTANT:

Improper cleaning of the dome cover may cause the rain wash coating to become less effective. In this case, in order to have effective rain wash coating, a new dome cover must be purchased to replace the existing dome cover. Consult with your dealer or con- struction contractor.

The camera position may be moved inadvertently while cleaning the camera body. Restart the product or refresh the camera position (position refresh) to correct the camera position. Refer to the Operating Instructions on the provided CD-ROM for further information.

Transmission interval

Image transmission interval may become slow depending on the network environment, PC performance, shooting subject, access number, etc.

When the following message appears on the screen during use

CAUTION:

POWER SUPPLY IS ONLY INTENDED FOR USE OF POE+(CLASS4) HUB -IEEE802.3AT COMPLY OR

AC24V MIN3.5A CLASS2 SUPPLY

The product may not be connected to a proper power- supply device. Check whether the power supply device in use is compatible with PoE+ (IEEE802.3at compliant). Or use 24 V AC power supply.

10

Image 10
Contents PGQX1224YA Cs0313-1043Can ICES-3A/NMB-3A Contents Important safety instructions Limitation of liability Disclaimer of warrantyPreface Main functions CPU System requirements for a PCIntel CoreTM 2 Duo 2.4 GHz or faster recommended Copyright Trademarks and registered trademarksNetwork security Precautions Turn the power off when cleaning this product Do not damage the power cableCorrectly perform all wiring This product has no power switchAbout SD memory card Periodically images on the screen appear to be dis- tortedWhat to do if Warming UP-PLEASE Wait appears on the display Code labelPosition refresh Tilt angles and the zoom ratioPrecautions for installation Time & date setting Check before installationPoE+ Power over Ethernet Plus Take notice of humidityMajor operating controls Main bodyOFF šON Initialize the camera Turn off the power of the cameraStep Insert/remove an SD memory card How to insert an SD memory cardWhen inserting an SD memory card, make sure the direction Remove the locking screw of the water-resistant capHow to remove the SD memory card Installations/Connections Power Source IEC/EN/UL/CSAHow to detach the housing base When using the wall mount bracket WV-Q122 option InstallationInstall the mounting bracket When using the mount bracket custom-madePlate spring Projection Dents Wire Detach the hooks Front/rear sunshields xing screw 8P alarm cable connector ConnectionHow to assemble the 24 V AC power supply con- nector kit AC power supply connector kit accessoryRecommended specification of cable wire Output cable for the monitor used for adjustmentMicrophone/line input cable External I/O cableRatings Audio output cableRequired cable Connection exampleLAN cable category 5e or better, cross LAN cable category 5e or better, straight Configure the network settings Configuring the camera so that it can be accessed from a PCPage Troubleshooting Power cable insulation is Damaged Live indicator keeps onLive indicator lights red Power cable, plugOperation status Indicator status About the live indicatorCamera when there are It is hard to see images withAlarm in 3 AUX OUT x1 each SpecificationsAlarm in 1 BLACK/WHITE IN/ Alarm in 2 Alarm OUT Terminal 1, Terminal 2, and TerminalLens ATW1/ ATW2/ AWCJpeg Mjpeg MLD, ICMP, ARPBB-HCA8A Standard accessoriesOptional accessories BB-HCA8CEPage Page Page Page Page Page Panasonic Corporation For business users in the European UnionFor U.S. and CanadaFor Europe and other countries Http//panasonic.net