Panasonic WV-SW598 Take notice of humidity, Heater unit, Influence on images and their quality

Page 14

Take notice of humidity.

Install this product when the humidity is low. If this product is installed during rainfall or when there is high humidity, the inside may be exposed to moisture and the dome cover may become foggy.

Heater unit

This product is equipped with an internal heater unit for use in cold climates. The product can be used in temper- atures as low as –30 °C {–22 °F} when connected to a PoE+ hub and –50 °C {–58 °F} when connected to a 24 V AC power supply or a tested PoE injector. The heater unit turns on automatically when the temperature inside the product drops below +10 °C {50 °F}. However, in an extremely low-temperature environment below –30 °C {–22 °F}, snow and frost may not be defrosted from the dome cover. When using the product in cold climates, take notice of the ambient and internal temperatures of the product.

When this product is installed and operated in low tem- peratures below –10 °C {14 °F}, normal images may not be obtained immediately after startup. In such a case, wait around 2 hours or more, and turn on the power again.

Influence on images and their quality

This product has no wiper unit. Under the following condi- tions, image quality may deteriorate or images may not be viewed properly.

(1)Influence by rainfall

Due to the wind that accompanies rainfall, images may be less viewable.

(2)Influence by snowfall

Due to the wind that accompanies snowfall, snow may fall on the dome cover. Images may not be able to be viewed through the areas of the dome that have snow on it. (The visibility may vary depending on the amount and type of snow.)

(3)Influence by dust in the air or gas emission from vehi- cles

Depending on the installation environment, dome cover may become dirty due to dust in the air or gas emission from vehicles. This may degrade the quality of images.

Check before installation

Compatibility of devices is restricted. Before installation, check the ratings and dimensions of the devices to be used.

Contact your dealer for details.

Router

When connecting this product to the Internet, use a broadband router with the port forwarding function (NAT, IP masquerade).

Refer to the Operating Instructions on the provided CD-ROM for further information about the port forwarding function.

PoE+ (Power over Ethernet Plus)

Use a PoE+ hub/device that is compliant with IEEE802.3at standard.

It is impossible to supply the power to this product from a PoE hub that is compliant with IEEE802.3af standard.

Time & date setting

It is necessary to set the time & date before putting this product into operation. Refer to the Operating Instructions on the provided CD-ROM for descriptions of how to per- form the settings.

14

Image 14
Contents PGQX1224YA Cs0313-1043Can ICES-3A/NMB-3A Contents Important safety instructions Preface Disclaimer of warrantyLimitation of liability Main functions Intel CoreTM 2 Duo 2.4 GHz or faster recommended System requirements for a PCCPU Network security Trademarks and registered trademarksCopyright Precautions Turn the power off when cleaning this product Do not damage the power cableCorrectly perform all wiring This product has no power switchAbout SD memory card Periodically images on the screen appear to be dis- tortedWhat to do if Warming UP-PLEASE Wait appears on the display Code labelPosition refresh Tilt angles and the zoom ratioPrecautions for installation Time & date setting Check before installationPoE+ Power over Ethernet Plus Take notice of humidityMajor operating controls Main bodyOFF šON Step Turn off the power of the cameraInitialize the camera Insert/remove an SD memory card How to insert an SD memory cardWhen inserting an SD memory card, make sure the direction Remove the locking screw of the water-resistant capHow to remove the SD memory card Installations/Connections Power Source IEC/EN/UL/CSAHow to detach the housing base When using the wall mount bracket WV-Q122 option InstallationInstall the mounting bracket When using the mount bracket custom-madePlate spring Projection Dents Wire Detach the hooks Front/rear sunshields xing screw 8P alarm cable connector ConnectionHow to assemble the 24 V AC power supply con- nector kit AC power supply connector kit accessoryRecommended specification of cable wire Output cable for the monitor used for adjustmentMicrophone/line input cable External I/O cableRatings Audio output cableLAN cable category 5e or better, cross Connection exampleRequired cable LAN cable category 5e or better, straight Configure the network settings Configuring the camera so that it can be accessed from a PCPage Troubleshooting Power cable insulation is Damaged Live indicator keeps onLive indicator lights red Power cable, plugOperation status Indicator status About the live indicatorCamera when there are It is hard to see images withAlarm in 3 AUX OUT x1 each SpecificationsAlarm in 1 BLACK/WHITE IN/ Alarm in 2 Alarm OUT Terminal 1, Terminal 2, and TerminalLens ATW1/ ATW2/ AWCJpeg Mjpeg MLD, ICMP, ARPBB-HCA8A Standard accessoriesOptional accessories BB-HCA8CEPage Page Page Page Page Page Panasonic Corporation For business users in the European UnionFor U.S. and CanadaFor Europe and other countries Http//panasonic.net