Periodically images on the screen appear to be dis- torted
When the camera is installed in a location where it is sub- ject to small vibrations (for example, when it is installed near devices that vibrate), images may appear distorted and stretched lengthways. This phenomenon is a charac- teristic of image pickup devices that use CMOS sensors and is caused by the relationship between the periodic movements of the camera and the timing that the image sensor reads images. This is not a problem with the cam- era. To reduce the possibility of this phenomenon occur- ring, install the camera in a secure location.
What to do if “WARMING UP-PLEASE WAIT” appears on the display.
This message indicates that the temperature inside the camera has become extremely low.
In such a case, wait until the heater unit of the camera raises the internal temperature (for around 2 hours or more in low temperatures below
About SD memory card
•Before removing the SD memory card, make sure to select “Not use” for “SD memory card” on the [SD memory card] tab of “Basic” page on the setup menu first. (☞ Operating Instructions (included in the
•When using an unformatted SD memory card, format it using this product. Recorded data on the SD mem- ory card will be deleted when formatted. If an unfor- matted SD memory card or an SD memory card for- matted with other devices is used, this product may not work properly or performance deterioration may be caused. Refer to the Operating Instructions on the provided
•When some SD memory cards are used with this product, the product may not work properly or perfor- mance deterioration may be caused. Use the SD memory cards recommended in page 38.
Code label
The code labels (accessory) are required at inquiry for trouble. Use caution not to lose these labels. It is recom- mended to paste one of the labels onto the
About the MOS image sensor
•When continuously shooting a bright light source such as a spotlight, the color filter of the MOS image sen- sor may become deteriorated and this may cause dis- coloration. Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period, the discoloration may remain.
•When shooting
AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.
SEE HTTP://WWW.MPEGLA.COM
Consumable parts
The following are consumables: Replace them in accor- dance with their operating lifetimes. Their operating life- times vary depending on the usage environment and con- ditions. The operating lifetimes below are just guides for when using the camera at +35 °C {95 °F}.
•Lens unit, panning motor, tilting motor, flat cable for tilting: Approx. 3.7 million operations (Approx. 20000 hours)
Cooling fan: Approx. 52000 hours
Slip ring: Approx. 3.7 million operations (Approx. 20000 hours)
About the automatic status detection function
When this product malfunctions due to exogenous noise, etc. for 30 seconds or more, the product will automatically reset and will return to normal state. When the product is reset, initialization will be carried out as when the power of the product is turned on. When the product repeatedly resets, exogenous noise level around the product may be high and that may cause malfunction. Contact your dealer for instructions.
About the dehumidifying device
This product has dehumidifying device to keep the inside at low moisture level, preventing condensation and quickly dissipating dew if produced.
Dew may be produced depending on the conditions of temperature, humidity, winds, and rain, and it may take time to dehumidify.
Lens and pan/tilt head
If a lens and pan/tilt head are not performed for a long period of time, the grease coating inside these parts may become sticky. That may obstruct the parts from moving. To prevent this, move the lens or pan/tilt head periodically. Or perform position refresh periodically in the manner described in “Position refresh”.
11