Panasonic WV-SW598 installation instructions Plate spring Projection

Page 23

Step 4

Mount the camera to the bracket.

qAttach the housing base to the mount bracket using the hexagon screws (M5, 4 pcs.) attached to the housing base*.

(Recommended tightening torque: 2.45 N·m {1.81 lbf·ft})

The “REAR” mark of the housing base shall be direct- ed to the wire hook section.

*Special screw: These screws are hexagon screws. Use an M5 hexagon wrench.

Hexagon screws (M5, 4 pcs.) attached to the housing base

Wire hook section

Housing base

w Make sure that the projection of the plate spring on the upper side of the camera is located on the “START” position. If not, turn the plate clockwise to locate the projection at the “START” position.

Plate spring

Projection

Plate

eConnect the safety wire (accessory) to the mount bracket. Refer to the operating instructions of the mount bracket for further information about where to con- nect the safety wire.

When using the optional mounting bracket (WV-Q122), connect the safety wire near to the cam- era as shown in the example below.

<Installation example>

Safety wire

rAttach the camera to the housing base. When attach- ing the camera to the housing base, the positioning pin on the upper side of the camera shall be on the “REAR” side. Make sure that the camera is securely attached to the mount bracket by turning the camera to the direction of the arrow as illustrated. Then, secure the camera to the mount bracket with the screws* removed when detaching the housing base.

(Recommended tightening torque: 2.45 N·m

{1.81 lbf·ft})

*Special screw (Fixing screw): These screws are hexa- gon screws. Use an M5 hexagon wrench.

Overhead view

Positioning pin

When the camera is

When the camera is secured

attached

to the mount bracket

23

Image 23
Contents Cs0313-1043 PGQX1224YACan ICES-3A/NMB-3A Contents Important safety instructions Preface Disclaimer of warrantyLimitation of liability Main functions Intel CoreTM 2 Duo 2.4 GHz or faster recommended System requirements for a PCCPU Network security Trademarks and registered trademarksCopyright Precautions This product has no power switch Do not damage the power cableCorrectly perform all wiring Turn the power off when cleaning this productCode label Periodically images on the screen appear to be dis- tortedWhat to do if Warming UP-PLEASE Wait appears on the display About SD memory cardTilt angles and the zoom ratio Position refreshPrecautions for installation Take notice of humidity Check before installationPoE+ Power over Ethernet Plus Time & date settingMain body Major operating controlsOFF šON Step Turn off the power of the cameraInitialize the camera Remove the locking screw of the water-resistant cap How to insert an SD memory cardWhen inserting an SD memory card, make sure the direction Insert/remove an SD memory cardHow to remove the SD memory card Power Source IEC/EN/UL/CSA Installations/ConnectionsHow to detach the housing base When using the mount bracket custom-made InstallationInstall the mounting bracket When using the wall mount bracket WV-Q122 optionPlate spring Projection Dents Wire Detach the hooks Front/rear sunshields xing screw Connection 8P alarm cable connectorOutput cable for the monitor used for adjustment AC power supply connector kit accessoryRecommended specification of cable wire How to assemble the 24 V AC power supply con- nector kitAudio output cable External I/O cableRatings Microphone/line input cableLAN cable category 5e or better, cross Connection exampleRequired cable LAN cable category 5e or better, straight Configuring the camera so that it can be accessed from a PC Configure the network settingsPage Troubleshooting Power cable, plug Live indicator keeps onLive indicator lights red Power cable insulation is DamagedIt is hard to see images with About the live indicatorCamera when there are Operation status Indicator statusTerminal 1, Terminal 2, and Terminal SpecificationsAlarm in 1 BLACK/WHITE IN/ Alarm in 2 Alarm OUT Alarm in 3 AUX OUT x1 eachATW1/ ATW2/ AWC LensMLD, ICMP, ARP Jpeg MjpegBB-HCA8CE Standard accessoriesOptional accessories BB-HCA8APage Page Page Page Page Page Http//panasonic.net For business users in the European UnionFor U.S. and CanadaFor Europe and other countries Panasonic Corporation